3d model of link

I also made it round to reduce print time eliminate the chance of corners peeling away from build plate.Lastly, I made the holes "through-holes" so there's more meat to install the peg as well as if you need to tap them out if they are too snug.I...

*Safety* There is a loop for an aider to be fixed in place over top of the though bolt. see pic, setup for 1" climbing rated tubular webbing. you figure out best way to mount it. Hardware needed would include Good high strength 1x1" alum tube 16"...

Mount the fan support on top of this guide. Print both STLs, sand a little bit and glue (ABS glues well with acetone). Sand again, and refit the holes with a 3 mm bit. - - - Needed stuff: 4 x M3 screws - 20 mm long (fan to fan-plate &...

Need: 4 ball bearings 5x11x4 4 M4x16 / 20 screws 4 M4x50 screws + nuts + springs 2 M5x50 hexagonal screws + stop nuts 2 extruder wheels diameter 11mm like on the photo 1 pneufit M6 Tested for more than 10 hours of printing without problems. Better...

bitte verwenden sie nur die beiden Original schrauben um den Ohrmuschelbügel an der Rückplatte zu befestigen. Angaben für die Druckeinstellung habe ich als Bilddatei Angefügt. Ich würde mich über einen Like freuen und happy Printig Tip Designer...

Also cut and cover the yellow wire as it's not needed.Use hot glue/tape/tack to stick the buck converter to the side of the duct and mount the fan at the top using the M3 screws.Plug the original connector back into the hot end board.Hotend board 24V...

You'll need the following parts: * Screws that fit Nerf guns * Short but sturdy screws * A flywheel left and right part * Two halves of a bottom rail * Front cover with picatinny on the bottom (smooth one) * Rear sight Mk2 * Empty holes for night...

You have the option of printing the whole hair in one color, or using our "unicorn hair" file, which we used in our photos. You'll also find separate files for the case and face/neck combo, so you can print them in different colors too! And finally,...

Also, i design one half of the case (e.g. just holding 2 batteries) and then mirror the body before any final surface features (such as embossed or engraved text).</p> <p>After an .stl is output from Fusion, I run it through <a...

By 'industrial source,' I'm referring to a configuration that differs from the standard ATX power supply pin start, requiring an adaptation of a relay to serve as the power-on trigger. Here's the custom case designed to house all electronic...

Items: a.co/d/9eBgPwW - dupont wire connectors a.aliexpress.com/_m0tgLcg - prism a.co/d/3Y0aKh0 - raspberry pi pico https://www.amazon.ca/dp/B0983P263K?ref=ppx_pop_mob_ap_share - ST7735 TFT display Tutorial:...

Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: slot_depth is set at...

~Size (H x L x W) (TOTAL) (Based on Fusion360): 55.5mm x 185mm x 121.40mm Sizes: To minimize printing time, the walls have a width of 1.5mm (final result may vary based on filament and other factors). This means the walls are relatively thin. This...

This is a remix of the Butter Robot Xiaofang by Simomura, and also uses the Rick and Morty Butter Bot Wyze Adapter by Capt Obvious. I expanded the Base to fit a Raspberry Pi 3 or 4 and added a spot for a 30mm fan in the top. The Tracks are in TPU and...

Here is the rewritten text: Arduino Project for Automatic Door Lock ===================================== Are you tired of fumbling with keys or struggling to lock your door? Look no further! In this exciting Arduino project, we'll show you how to...

If the slotted caps happen to print with the bottom of the slot connected like mine did just clip it with with pliers and remove the little nib. Slip them over the wires and push into the conduit, they'll go in a lot easier than the solid ones. ...

Y holder motor upgrade for Prusa Mk3 Mk3s Mk3s+&nbsp;Upgrade your Nema 17 mount to improve vibrations, noise, belt alignment and rigidity.→ Easy screwed to panel with strong ruthex M3 Threaded inserts.→ 1mm gap between motor and rear panel.→ x3...

Customized Version of Thingiverse's Project 739573 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions for Creating Your Own Customized Text-Based Design: Using the Following Options: text_thickness:...

Have a look here: https://www.printables.com/de/@MakerTeam/collections/1011820Material: PLA/PETGLayerheight: 0.3mm or betterInfill: 20%************************************A nice and easy COOKIE RECIPE:250 g Flour1 tsp Baking Powder100 g Sugar125 g...

This sensor allows the MachTach to measure the speed of a machine by monitoring a gear with up to 90 teeth. The MachTach is a machine tachometer that displays speed in RPMs, Surface Feet Per Minute and Surface Meters Per Minute. You may use this...

### WARNING According to California law, to AVOID classification as Assault Weapon your ASSEMBLED (ready-to-fire) gun need to be in any of these configurations (or both, if you wish): 1. no "evil features" like pistol grip etc. a.k.a. "featureless" ...

The Flexmounts system revolutionizes the mounting of action cameras on FPV drones. Slide in, in seconds, without tools. Visit my social media for more shots and insights. The Flexmount System makes it possible to mount (almoast) any action camera on...

The rack is 4U high, with about 1cm of space above and below each bay for airflow. Each bay features a 40mm fan from Fractal Design (http://www.fractal-design.com/home/product/casefans/silent-series-r3/silent-series-r3-40mm), with fan holes spaced at...

2 pieces 10mm linear shaft 440mm 4 pieces of linear shaft holder 10mm TR 8 lead screw 365mm long 4mm pitch single-thread (can vary / you should check before buying just do one turn on the spindle and measure from the hotend to the bed) Shaft...

It's designed for smaller objects like caliper boxes. Einkaufsliste: M2 screws 8mm long: Click here! Nails Ø1,4mm: Click here! This is my version of a hinge. ...It's perfect for smaller items like caliper boxes.</p> <p><strong>Shopping list:...

This multi-device charger is built around a standard USB charger, capable of powering up to five devices simultaneously. One USB port features Qualcomm fast-charge technology. I've included STEP and 3FD files for users who want to customize the...

Here's an example build for getting started in the world of mini quads on a budget: Motors: BR2205-2300KV ESCs: RS20A-V2 Flight controller: Naze 32 Propellers: Kingkong-5040-5x4x3-3-Blade To complete the build, you'll also need nylon spacer screws,...

This sensor allows the MachTach to measure the speed of a machine by monitoring a gear with up to 90 teeth. The MachTach is a machine tachometer that displays speed in RPMs, Surface Feet Per Minute and Surface Meters Per Minute. You may use this...

To do this, you need a power bank and lots of resistance. As shown in the tutorial at https://www.youtube.com/watch?v=Dp3RMb0e1eA&index=3&list=PLVilroPGLJaesaS5mP93i0goPck2JK-O4. You can also find more information on GitHub at...

Modified version of http://www.thingiverse.com/thing:243650 created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=243650 Instructions: Using the following options: box\_maximum\_length\_or\_width = 80 tolerance = .5...