3d model of geometrical shapes

Born from a passion for photography, art, and astronomy, Solarcan is a unique camera designed to capture extreme time exposures of the Sun's path across the sky. It comes pre-loaded with photographic paper, precision drilled pinhole plus cover,...

I absolutely love the design of thing:1100601, but the components are too expensive and add up close to 100 dollars. So I found this lovely design and remixed it. I added two tunnels, one that goes to the front and another that goes to the top,...

Since the SD reader is at the back of the LCD, the cover I made is boxier than I would like. When I get an extender for the reader, I'll design a cover that sits more flush. ##**Shopping List** * For the fans, M4 x 12mm screws (x8) and M4 nuts...

The inspiration behind this project comes from Autonomous Plant - Proof of Concept found on YouTube at https://www.youtube.com/watch?v=XFOcX6E8lGI. So far, the following parts have been created: A bottle funnel was remixed from a design available...

After a short period of use, we noticed that the PI was getting hot, so I added some slots at the top to allow for ventilation. I highly recommend coating the PI and the PiCan with a conformal coating if you plan to leave it in a vehicle for an...

dowl [4] Thing URL: http://www.thingiverse.com/thing:270957 [4] Thing Author: snowboarder [4] Thing Licence: Creative Commons - Attribution - Share Alike [5] Thing Title: Red Base 1 [5] Thing URL: http://www.thingiverse.com/thing:360405 [5] Thing...

FOLLOW US IN FACEBOOK: GROUP: https://www.facebook.com/groups/3DDruckSupport/ SITE: https://www.facebook.com/3DDruckSupport/?modal=admin_todo_tour...

Fits in the project Glowing LED and WLED all alphabet letters and all numbers 10 cm high.https://www.prusaprinters.org/prints/149829-glowing-led-and-wled-all-alphabet-letters-and-all-You are doing me a big favor by clicking the Like button...

For more info watch this video: https://www.youtube.com/watch?v=EUn47z4kyPc Additional hardware is also needed to include; Hillman #6 32 x 3/8 inch round combo with nuts machine screws (qty needed for project: 8 screws 8 nuts) Hillman #6 flat...

To remove the belly pan, trace a standard sized 3s battery and then dremmel it out - leave as much of the pan intact as possible, it will act as a shelf for the original Traxxas batt. Soldering is crucial - if you can't solder battery connectors,...

... I've produced several of these designs and found that when mounted with the two upper screws, they fit snugly together. I've used this design for some time now and am currently working on another version. Therefore, I decided to share it with you.

However, these printers are not ideal for PLA printing due to a lack of cooling fans and heat breaks that restrict airflow around printed parts. The extruder remains mounted on the X-carriage, which doesn't require significant lightening since ABS...

parts neededWhite PLA or PETGGlueBatteriesWhite lights with battery holder (I used these)2mm foamAssemblyMake 3 rectangles of 2x1 cm from the foam and stick them as in the photo. Take the lights and put them through the hole and press the battery...

Here are the parts you'll need: Raspberry Pi 3B or 3B+ for the brains of this operation A Raspberry Pi 7 inch touchscreen for an immersive experience Hifiberry AMP2 for crystal-clear audio A Micro SD card class 10 for storing all your tunes Some...

Items: a.co/d/9eBgPwW - dupont wire connectors a.aliexpress.com/_m0tgLcg - prism a.co/d/3Y0aKh0 - raspberry pi pico https://www.amazon.ca/dp/B0983P263K?ref=ppx_pop_mob_ap_share - ST7735 TFT display Tutorial:...

- 1x Micro Servo SG90 - 4x M3x5mm screws - Battery clips - 5 nails 1.4x25mm and a bit of DIY flair... The assembly should be self-explanatory based on the pictures. The sensor and servo cables have been shortened. Have fun with it and don't forget...

There is also a 'stock' which allows the part to sit comfortably and firmly in the palm of the users hand while in use. Files for the part both with and without my logo have been uploaded depending on the user's preference. Test conditions included...

The flight controller sits down nice and flat into it's mounting area with 2mm clearance underneath which is perfect to put a piece of double sided foam tape to hold the F3 down snug. This was specifically designed to work with TJ's designed frame...

The antennas are partially obscured by the all-metal PC case, which I suspect made for the unusable quality of my Bluetooth connections.I bought myself two RP-SMA extension cables to extend the antennas to a more suitable location: above my monitors,...

 Unlike other design that is held in place with metal nut and bolt, where wobble can occur on smaller drill bits. It's strange that we use metric in this country, but they were selling this set of imperial bits in the local hardware store...

This eradicates the frustration of dissecting the wire bundle to identify the break point. In the event that the ribbon cable wears out, a fresh one can be simply plugged in. Instructions These parts were designed to mount 25-pin...

An LED light strip was cut and 7 rows of lights were run; you probably don't need that many, but it's nice to have a bright display. A switch (Amazon link: [on/off...

... than 2mm). You won't need much holding power. **Note**: When I printed, I flipped the shell upside down and added supports for the surface that would be flush against the ceiling. Still plenty of supports to remove, but not _inside_ the shell.

Human: Customized version of http://www.thingiverse.com/thing:53235\nCreated with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=53235\n\n \n \n Instructions\nUsing the following...

The provided g-code has little support for printing with PLA, which is easy to remove.When you print with PETG you may aslo need according to user experience some support for the overhang of the knob.================Das Original von Koray ist clever...

Tinkercad link: https://www.tinkercad.com/things/11G6wzWbg5A Some of my other designs: https://www.thingiverse.com/thing:4165457 - Smoke Stack Addon for Sector Mechanicus https://www.thingiverse.com/thing:4120637 - Sector Mechanicus Wall Link...

If rotating the screen display use both of these lines in the Pi config file: display_rotate=2 lcd_rotate=2 I wanted all cables to exit out one side only, so I added a 90-degree mini USB adapter to route the power cable the same direction as the USB...

________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Tinkercad link: https://www.tinkercad.com/things/iiZRfDyotAN ________________________ Some of my other designs:...

By request, I had aded a mid version of the strain relieve, (15mm), with and without logo. He hecho este remix porque no he encontrado niguna cover del eje X para la sidewinder que combine aspecto y funcionalidad. Este se basa en el original de...

This insert does use allot of filament and will take a long time to print everything. This is for people who love this game and plan to bring out and play for many years. ... As always here is my TinkerCad Link to these files...