3d model drawing

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

print the uppers in a 100% infill! Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

head), I recommend staying in a 18-25 mm range for the thread length, to give yourself some margin.For my US friends using imperial, you can use #4 screws but you will need to adjust the nut parameter in the f3d file.Also, I think it doesn't leave...

... self sustaining for long periods. All ground piping, cabling and the Large Gas collection cansiters would be covered in Dirt once operational for Sun / wind shielding. Note the Space Suit man was inserted for size, got it from the NASA models site

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are resistant to oils, lubricants, and heat.The models are designed to fit an Eerie Tools SM-LTHM 7x14 lathe but...

 900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly.  If...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

Http://www.Thingiverse.Com/Apps/Customizer/Run?Thing_id=507810 Instructions Using the Following Options: Custom_phone_width = 100 custom_bottom_fillet_resolution = 8 printer_tolerance = 0.4 stencil_vertical_position = 50 custom_case_pattern_thickness...

 I have it installed on both my printers and it's really nize.MK3S and (+) versions of the adapter are unique to each model and not interchangeable.Both adapters drop in over the screw heads as shown and get trapped between the extruder body and...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

Its light and super stiff if printed in ABS 100% infill. Included are all the .STL files for all the models. The frame is quite light and stiff. I threw the frame over and over against a wall and from a 5th floor balcony and it survived...

The COMPLETE Svartwood Trolls bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Trolls comes in all size and varieties, and being one of the most ancient people, no one knows...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

Works with the regular rectangular heat sinks or the Waveshare heat sink.Two different styles of ventilation openingsSTEP files available for easy remixingThis remix does not currently have an option to mount a fan inside the enclosurePowering the...

I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

Basic overview:This is a drop in replacement barrel for the Dart Zone Solo Pro that is designed to allow it to fire mega darts, but I designed the model in a way that it can not only also still fire half darts, but fire rival ammo too! It shoots Mega...

You can use other sized bolts (M3 or M4) files are uploaded for adjustments, I can and will upload different sized models.* *OPTIONAL PARTS* 3x WASHERS (desired size) 3x Nyloc Nuts (desired size) #HOW TO PRINT During the design process I accidently...

 You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid.  This can be...

And Happy Printing!-------------------------------------------------Originally designed in Fusion 360 and printed with Prusa Mini+ THIS MODEL IS UNDER CC (Creative Commons) LICENCE. Note: The DO NOT EAT sign might not print properly due to...

:DI put 3 holes in the top of the soap container where you can store your toothbrush or similar bathroom itemsI hope you enjoy the model and just try it out for yourself.I have written a description of how to make the soap here, which should give you...