3d model customization

I simply used a couple of dabs of model car glue, but you can use epoxy if you prefer. I would avoid CA because the fumes may fog up the inside of the lens. The finished part is shown in "modified camera.jpg." I just checked Amazon and found that I...

This would not work on a single nozzle printer, so we opted for truncated tetrahedra with slight insets on two of their triangular faces. INSTRUCTIONS Everything prints at 0.2 mm layer height.Set your line width to 0.45 mm, as the pattern...

It provides a list of the models. A typical tower includes mostly about 20-30 function calls, generating Lego block elements plus some openSCAD "hand code". If you download the full Doblo Factory code (http://edutechwiki.unige.ch/en/Doblo_factory,...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

One suggestion offered is to quickly wave fire under the problem area in the hopes that the hair will burn away before the plastic is damage, but I came up with a different solution.This set of models replaces the entire front wheel assembly. The...

More information: The models were printed in PetG and have a consumption between 5.7g and 7.0g and the printing times range from 0:47 to 1:15 hour. Note1: If the z selection alignment is used, you can generate a line as the one shown in the...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Ranger from Nan Thalias. Ervion was sent as part of an Elven diplomat’s escort, alongside his father which was attacked by a retinue of goblins and bandits near the County...

This is a remix of my previous models: [Modular Wahoo Board Remix](https://www.thingiverse.com/thing:4207631) [Modular Wahoo Board Remix Case](https://www.thingiverse.com/thing:4302373) In this new version, I have opted for a singular base with...

Initially I modelled the candle I wanted, then using boolean operations subtracted it from a cube, and split the cube in half. ...Then I added the pins and matching holes just to help align the boxes and hold them together a bit by padding and pocketing...

This is resistant to everyday wear and tear, but we got warned that rust stains are not completely removable.So a stainless clothes drying rack became necessary.Most commercial ones just have powder-coated steel tubes which rust after some...

So I grabbed [YucA305](https://www.thingiverse.com/yuca305/designs)'s [Drag_Chain_YZ_Slipon.stl](https://www.thingiverse.com/thing:4648673), put it into SketchUp Online, used the STL as a mask for sizes and alignment, simplified the model a bit and...

On the single phase motor models there's contactors and timers in there for the auto tapping function... if fitted. I wired the 12 volt psu's mains connection to the main switch of the mill, this is after the main fuse so it's protected by that,...

What's IncludedThe entire Anvil Digital Forge Patreon release for January 2024, including; Multi-Shell Options:A number of STLs are labled with "(Multi Shell)" - these files can be imported into Blender (reccomended), or Meshmixer, or various other...

That link also calls for using alanho's file to hold the TFT50, here is a direct link to his page as well: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/alanho/BTT_PITFT50_v2_Mount I also made some simple changes such that it...

*Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit.* **UPDATES** **V3.3** (slight comfort improvements over v3.2). [print 1 for each eye] **Added a version for the prescription inserts from VR Lens...

 The SFX version backplate does not fit the build plate of a Prusa Mk3, so this project is temporarily on the pre-prototyping stage.For the FlexATX version, click this link. The enclosed design includes two types of motherboard trays of...

This meant adding three holes for screws, and I also added flanges on the bottom in an attempt to mount the fan shroud I modified for my model cooling fan shroud. I left the sensor port alone for now - I may or may not try using the cooling fan...

Fits Both "Research" and "Research Plus" Models. Don't Lose Precious Time with Clips or Carousels! Print *Your* Holder **Now** ;-) # Materials Required - 4mm Aluminum Rod (2x 18cm Minimum) - 2x M5 20mm Screw With Hex Head - 2x M5 Butterfly Nut -...

Already renowned for their authentic sound, Casio's latest model takes it to the next level with its impossibly small footprint. Measuring 43 percent smaller than previous generation Privia instruments, the PX S1000 is literally half the size of...

To do this I went to https://3dp.rocks/lithophane/ sized it in model settings, and set it to Positive under image settings. I kept it flat since it will be used as the back of the bookstand. But while it's not in use it can also be used as a cool...

... <p>100%</p> <p><strong>Notes:</strong></p> <p>Print at 100% infill. The tubes are modeled hollow and should print that way Post-Printing Top Finishing Some finishing may be required for the Elite version of the top. Category: R/C Vehicles

Safety Information Please be aware that this product contains small items and is not suitable for young children.This product is a scale model and is intended for use by adults and children age 14+.Take care during use as some products may...

This is the first 3-D model I have built from scratch and I was looking to get it done quickly. So, I kept it simple but did note that it wouldn't take much to add a few more amenities that would suit personal needs or desires. The router fits...

There is also a reverse mount for the hygrometer that's for mounting it on the inside of glass (also fits stock model).The hygrometer has an extender for the button that switches between C\F. You will need the original rubber insert...

It's also compatible with the Chinese clones of both these models, often referred to as "J-head" extruders. There is a cable guide built into the design which will assist with keeping everything tidy and reduce any stress on the heater and thermistor...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

The first number at the end of each model's filename is the size of the PVC post that the adapter is intended to go on top of, the second number is the size of the PVC pipe that the finial would normally go on. I have a collection of Halloween things...

Update 01.04.2023 A friend i have made through the Neo Community have discovered that the clearance might not the good with the standart Neo, because the belt housing on the left stick out further, he have provided the file named...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...