3d model customization

The tolerances on these can be somewhat tight, but they came out beautifully on my Bambu X1C.Model specific notes follow:cards_box_1.stl, cards_box_2.stl - Print one of each. You can add color on layer 4 or 5 (depending on line height) to make the...

DescriptionThis is a fast and easy to print model to calibrate your new filament. It can be used to find the right settings for the extrusion factor to get the right wall thickness.</p><p>It is designed with a 0.86 mm wall thickness to meet the...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

to remove push from the angled face (from the thickest portion) outward and it will release itself from the extrusion.The ideal position is up against the top of the frame, tighten the extruder and make sure your PTFE tube is pushed in all the way,...

I've uploaded the STEP files, so feel free to remix the system to fit your printer model! Just give me a shout-out because it took a lot of hours, dozens of printed iterations, and plenty of PLA. The IR Probe is mounted to the connector by design...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

The model isn't geometrically perfect as I did the scaling in blender (The only editor I know how to use), but it works which to me is the most important thing. You will need a couple screws to put it together as the ones which come with the...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would...

The firmware numbers will match regardless of your printer model. If you use a slicer that requires EEPROM, make sure to update your EEPROM settings to match your new firmware. The easiest part is printing the adapter plate - any ABS or PLA preset...

**My Tinkercad-works:** [Coverplates + Hinges + Z&Y-FrameChainmount + Connectos-Hub + cutout-stamp](https://www.tinkercad.com/things/60ksBr4wvsb-s8-pro-coverplate-hinge/) [Hotend Mount + Y-Axis Chain...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

The one thing most existing models seem to be missing is the funky characters on the keys. I looked around and found a font that looks just like what they used (basically an old computer font like the one used at the bottom of checks, ...) As I...

- Replaced PZ20 circuit's LDO with a simpler model with higher input voltage range - Added second LDO for dedicated supply to LED's - Isolated TH1 from ground plane to address vdroop effecting thermal readings - Added grounding vias for edges and...

I used this here: https://de.banggood.com/Remo-B5509-Ball-Bearings-593mm-For-1621-1625-1631-1635-1651-1655-RC-Vehicle-Models-p-1450586.html - 9x M3 30mm screws and nuts to conetc top and bottom trays - otionally: 9x M3 0.5mm washers to put between...

Entry point for USB wire, hole has a separate part for covering it: + usb_wire_cover - base_bracket2_corner_RH x1 - base_bracket2_corner_RH_back x1 - base_cover_big x2 - base_cover_small x3 - base_cover_corner x2 * Front covers: base model is...

Licensed models were manufactured in Germany, Sweden and Russia First Fighter The Type L is famous for being used by Roland Garros to shoot down three German aircraft in April of 1915. This was a special single-seat arrangement made for the tennis...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

I found models of the servo, Sharpie, and 28BYJ-48 stepper motor on GrabCAD, but didn't include them in the Fusion 360 assembly file here. The build log for my printer can be viewed here: https://openbuilds.com/builds/a-rolling-plotter.9207/ ...

This first model is referred to as the MK1.An enhanced PLA is sufficient for the low temp extruder, but it will not stand up to the heat when using the high temp extruder in an enclosed chamber. For the high temp I used eSuns PA-CF.The high and low...

I made a small update to it, adding the model with the included screw threads in the back, and ever since that update the thing is still there but returns a 404 error for everyone who isn't me. I've tried to get it to post, I contacted thingiverse...

... the bodies for proper orientation on your print bed. 3. The majority of the model is parametric. ...I tried to describe each parameter well, but you may need to jump around to through the sketches and features to find the correct ones to change.

On my version, I suggest that you start with 4 seeds in each of the 12 pits (print 4 copies of the 12 seed model and then separate them using nail clippers or small scissors). Increase the number of seeds in each pit progressively to increase the...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...

Depending on the figurine put on top of the box a different playlist ist played, currently mostly kids audio books and a spotify music playlist.All in all a very cool project that i hope to expand when my son grows older.ElectronicsPhonieboxRaspberry...

As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the platform, using a belt to drive the capstan. I would...

... (option code 772). From VIN F060888 1999 Mercedes-Benz CLK430 Base Coupe 2-Door 4.3L 4266CC V8 GAS SOHC Naturally Aspirated Included formats: *.obj, *.stl, *.3mf All dimensions are accurate. This model printed and tested successfully.