3d model brain

EX6 Arcade Fight Stick What started as just doing a few tweaks to an existing model turned into a near full redesign and a (almost) fully printable arcade/fight stick case platform; the EX6. Printable on the Ender 3 or any 200x200 printer. The...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

:DI put 3 holes in the top of the soap container where you can store your toothbrush or similar bathroom itemsI hope you enjoy the model and just try it out for yourself.I have written a description of how to make the soap here, which should give you...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

In short, it means that we will be using the Name Tag creator  to make the base (and thus be able to add text, image files, &c), and then create fitting covers and holders in this program. (A mixed approach is to also create the base with...

I was unaware that the MMU2S required changes to the extruder and almost decided to hold off and just install the SPA by itself, but I started poking through the assembly manual for the MMU2S and realized there were changes that needed to be made to...

Also this shape is very special because you can use two V Plate and invert one to create a sort of "wave" that visually connect two I plate that is place up and down.Double C Plate* : This isn't a stand alone plate, this mean this plate is useless on...

Ich habe mich bemüht alles genau aufzuschreiben, vielleicht habe ich ja aber doch etwas übersehen. Beim ChaosRun handelt es sich um ein kleines 3D gedrucktes LED Spiel für den kleinen oder großen Zeitvertreib und je nach Spiel für bis zu vier...

No short circuits between the V G and/or S wires. Hardware I used these end-stops: https://aliexpress.com/item/32959048821.html I am not affiliated with AliExpress nor TwoTrees and there are LOADS of identical/rebranded switches out there. You will...

If you want detailed instructions with pictures, please see my instructable on http://www.instructables.com/id/The-Bicycle-Bubble-Machine/ Apart from printed parts, you will need: a piece of wood to mount the machine on, which will then be put onto...

A take on norwegiancreation's PID ball balancing seesaw using an Arduino.Video of this...

A challenging learning toy … but perhaps also a clock for the one or other adult 3D printing fan.I got the inspiration for this project from a contribution on Thingiverse (https://www.thingiverse.com/thing:2852026). I completely redesigned the case...

Cómo configurar los parámetros para personalizar la impresión del prolongador para asa de maleta 2.1. Para poder personalizar el prolongador para asa de maleta deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de...

Beim ChaosRun handelt es sich um ein kleines 3D gedrucktes LED Spiel für den kleinen oder großen Zeitvertreib und je nach Spiel für bis zu vier Spieler. Die Grundidee habe ich von hier übernommen: ...

Print instructionsCategory: 3D Printer Parts Summary I've been enjoying using the stock inductive Z endstop as a bed probe on my Artillery Genius, but was suffering a bit from its temperature sensitivity: I was noticing that at different times of...

Cómo configurar los parámetros para personalizar la impresión del soporte de maleta para silla de ruedas V2 2.1. Para poder personalizar el soporte de maleta deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de...

... Now I could home the printer and send it to 0,0,0 and the needle should go right to the front left corner which it did.Print SettingsPrinter:Qidi X-ProRafts:NoSupports:NoResolution:.15Infill:20Filament: Hatchbox PLABlackCategory: 3D Printer Parts

You have to look very carefully at the top side to see that it is 3D printed. That said, I think I prefer the look of the first version. It is more special with the black part laying on top of the white background.</li></ol><p>Note that the .stl...

This is my design of a toy meant to teach children about the effects of an inclined plane on a rope/pulley system and the forces involved.  There are 4 3D printed parts in total and 7 externally sourced common hardware materials.  OpenSCAD Source...

:)All of the parts in this project are designed to be 3D-printable without supports, and they're modular, meaning you can choose how many "planter" modules to put together to build your tower.The planter modules come in two varieties: modules which...

If you encounter any layer separation or odd layer squish patterns that were not there before, ensure that the anti-wobble is not allowing any movement in the Z axis direction and adjust accordingly to make sure the pins cannot move up or down. ...

There is now an uploaded drilling guide that takes that into account. Update 8: The long awaited instructions document is now uploaded! Update 9, uploaded an updated Taz 6 specific endplate. There are several other related projects that are...