3d mars model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

The COMPLETE Maneater Nagarots I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Nagarots are a cult devoted to the Serpent Demon Yn'aga, herald of the Tyrant-God...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

 For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base.  The adhesive mount’s socket is smaller...

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons?</p><p>Feel free to remix it as you wish. It would be nice if you upload the...

&nbsp;I use a cheap little fingernail drill to do most of my sanding as a dremel can somtimes be overkill and it comes with a ton of little heads it'll take me years to use up.https://www.amazon.com/dp/B07T8H3531?ref=ppx_pop_mob_ap_shareThe final...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

I included notes at the end of what I would've ideally fixed if i had the time to spend on this design. Other Items You may need: 120mm fan with over 2lollipops of pressure u wont be pulling much air through those hepas 3 18650s and a bms if u want...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Note: I accidentally had two ⅔ marks on the outer ring in the original model. That has since been corrected but I haven't had a chance to print out a replacement, so the pictures still have the typo</p><h3>How to use</h3><p>Pick a measurement disk...

It's just a model I whipped up, and sliced it with a bunch of retraction changes. Then went back and spliced all the g-codes together. Base Cura profiles I use: layer height - 0.2mm Optimize wall print order (do not retract before outer wall), print...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

These are mainly meant for kitbashing digitally, so they might not work with existing citadel kasrkin/cadian models without a little work. For torsos I suggest Planetless Trooprs by LoggyK, these were the main inspiration behind the packs. Storm...

The model was inspired by [this map pocket on Amazon](http://a.co/5P0dMfJ), but larger and with more holes for the bungee cords. ...I have no affiliation with this product and my design was done by hand, so please don't sue me if that's your map pocket...

Also, my printed model needs some clean-up on the outer edges of the ducts (which you can see I did not do). You may have better results with your printer. Printing & Assembly notes: Save the 2 self-tapping case screws when you disassemble the...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

Supports: YesWhole star: If using Cura we recommend using the [Tree supports](https://support.ultimaker.com/hc/en-us/articles/360012614559-Experimental-settings) option and adding a 'Brim' to help the Tree supports adhere to your print bed Half...

It has been almost three months in the making, and several bits are an additional 100–200 sketches beyond the base model, which means there is a ton of Mf-detail, I probably overdid it. My goal was to create something special for kitbashing,...

For more details, visit http://www.thingiverse.com/thing:47032 [^] (v.1) naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 48...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Cursed Immortality Season 2 - (2/4) The Umbratouched - Curse of Vengeance   Description Save money on this complete December Bundle, The Umbratouched, Curse of Vengeance, which contains all the models from the December release! These models come...

The initial idea was to couple the two 4020s to the original TTBluer case, however it has lower flaps that made the process difficult, as I wanted to preserve the original part without cutting flaps, I decided to model a new case. I have results...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_pattern_thickness = .8 custom_back_extra_port_y_size = 30 custom_back_camera_corner_resolution = 8 custom_top_port_x_position = -10...

This meant adding three holes for screws, and I also added flanges on the bottom in an attempt to mount the fan shroud I modified for my model cooling fan shroud. I left the sensor port alone for now - I may or may not try using the cooling fan...