3d joint model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

DesignThis is the reduced to the max case / housing / sleeve for the Raspberry Pi Zero (2 W) in the version with cooling (we have another model that is prepared without cooling), less is hard to imagine. A foldable print in place housing with live...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   Among the first risen humans in Draksborne, Violet thought herself to be insane for her first life upon Tharador. For when she woke she remembered all that had...

But 100% fan power isn't necessary, so use an lower Value and take the 100% as "headroom" for bridging etc.The bed leveling is done with an single DC42 IR Sensor (I can highly recommend them). Printing and InstallationAll parts can be printed...

* Supports: Yes (if using Cura we recommend using the [Tree supports](https://support.ultimaker.com/hc/en-us/articles/360012614559-Experimental-settings) option and adding a 'Brim' to help the Tree supports adhere to your print bed) * Rafts: Doesn't...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

This set may fit other models. I can't make guarantees on fitment.\nAnyone familiar with the Makerbot series printers will know that it's quite dark in the build space. They provide you with a roving white LED, and a red AMBIANCE LED which is both...

Also, my printed model needs some clean-up on the outer edges of the ducts (which you can see I did not do). You may have better results with your printer. Printing & Assembly notes: Save the 2 self-tapping case screws when you disassemble the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I have no model or figure of Buffaloman in a camo tank top. The bazooka is actually pointing backwards to simply be held resting on his shoulder. I scaled it to 40% and positioned it to be resting between two shoulder spikes with the hand grip...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

... The models are in the position, they should be printed. No support is needed. I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this tall piece. Printed on an Ender 3 Have fun!

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

It has been almost three months in the making, and several bits are an additional 100–200 sketches beyond the base model, which means there is a ton of Mf-detail, I probably overdid it. My goal was to create something special for kitbashing,...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

The COMPLETE Maneater Nagarots I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Nagarots are a cult devoted to the Serpent Demon Yn'aga, herald of the Tyrant-God...

(Not required for revision 2) Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

Many thanks to Dalek_Kolt for providing the original model, you can find more ripped stuff from them here: https://www.vg-resource.com/thread-39778.htmlDisclaimer:The figure you see in the photos is a larger version that houses LEDs and batteries. If...

FLSUN doesn't seem to be OK with the idea of sharing the CAD models (their loss...), so I didn't include the machine parts I reverse engineered (the effector is present though). The extruder is very crudely made, so I left it. How to build : ...

I found the models of the servo, sharpie, & 28BYJ-48 stepper motor on grabcad, but didn't include them in the fusion 360 assembly file here. The build log of my printer can be found here: https://openbuilds.com/builds/a-rolling-plotter.9207/ Here...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

Existing models didn't meet my needs, so I created a parametric part. The current parameters are tuned for use with an M6 thread and prior tapping. I recommend printing a test part (produced by setting debug = true) to ensure your tolerances are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

Helicopter Collective Controller Work in progress. 6/17/20 Added File Added collective_open v4.f3d (An assembled model of all the parts.) You can alternatively use my Russian style grip located here:...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...