3d ide

For now, you can still place an order by emailing info@ide-3d.de. The IDE System comes with everything you need, including a power supply, controller, and build plate, all packaged in one complete unit. Simply plug it in, slide the build plate into...

Emulsion Tube/Main Jet assembly for Weber DCOE or IDE carburetor.Quick rendering again with CADRays application.

... cover. Required: (x8) M3x5 mm screws for single IDE To SD adapter (x12) M3x5 mm screws for dual IDE To SD adapters Optional: IDE extension cable ----- The 3.5" drive bay version is available at: https://www.thingiverse.com/thing:5642213 -----

This adds some security by clipping the rear of the board onto the drive.When you are ready to take the drive out for experimenting, just remove the IDE adapter board and slide the drive out!Print flat on its botton at .2mm layer height. ...preferably...

ORIGINAL SUMMARY [I didn't designed this Thing, I ONLY corrected the error from the STL file] ORIGINAL CREATOR: https://www.thingiverse.com/dogp/designs This is a bracket to install a CF->IDE adapter in an internal 3.5" hard drive bay. I collect...

... to solder it in place of the original SMD LED which you will want to remove (as it will shine through the plastic). https://www.hexin-technology.com/HXSP-2118P_CF_to_IDE_Adapter-Product-400.html http://www.soarland.com/CF_CFast-catalog-41.html

This is 3.5" bay enclosure for HX-2118P (also known as SLCI4001, HX-118, HXSP-2118P or HXSP-2108P) Compact Flash to IDE adapter. 4 variants available (wider and flush front as well as shorter and longer variant. Should fit most AT and ATX cases...

Remix - my sd to ide board is the 3 leds version, with the power jack (floppy) on the bottom. Made a hole to install an frontal usb, I've secured the cable with a cable tie and double sided tape. After testing, I didn't like the frontal leds (too...

Remixed from "PCI / ISA Slot Bracket for IDE 40pin to SD adapter", this adds the following enhancements: - Thicker triangle areas along the bracket so stress from inserting/removing the SD card doesn't flex the bracket as much. - Enclosed bracket...

This is a bracket for the IDE to SD card from https://www.amazon.com/gp/product/B07YFPX7JB There is a "long" and a normal version of the bracket; if using the normal version please verify the dimensions are correct as the "long" version has the...

Remixed from "PCI / ISA Slot Bracket for IDE 40pin to SD adapter", this adds the following enhancements: Thicker triangle areas along the bracket so stress from inserting/removing the SD card doesn't flex the bracket as much. Enclosed bracket screw...

This works great if you're using SATA drives in a SATA system, but it can be problematic if you're trying to adapt a SATA drive for use in an old PATA/IDE system. This adapter sets the 2.5" drive back far enough that you can fit a SATA-PATA adapter...

This is a bracket for the IDE to SD card from https://www.amazon.com/gp/product/B07YFPX7JBThere is a "long" and a normal version of the bracket; if using the normal version please verify the dimensions are correct as the "long" version has the latest...

This is a bracket for the IDE to SD card from https://www.amazon.com/gp/product/B07YFPX7JBThere is a "long" and a normal version of the bracket; if using the normal version please verify the dimensions are correct as the "long" version has the latest...

This is a remix to shorten up the mount a bit, and raise the cf card up off the floor on some standoffs. ...This also as a an overhang to keep the molex to berg cabling in check.

Originally 4-pin design by https://grabcad.com/german.a.mikheev-1 I just modified it to 3 pin.

A Straightforward Test for 3-1/2 Inch Hard Drives. Secure Horizontal Desktop Installation. ... Print Settings Details Printer Manufacturer Information Printer Model: Prusa i3, CoreXY Raft and Support Options Rafts Required: No Supports...

A remix to fit the back of the Checkmate 1500 case, needs 2 M3 screws and bolt to panel mount it.

Routing an LCD Ribbon Cable Using a Trunking Method for 2020 Extrusion Systems

This is a remix of a SD2IDE Adapter allowing to change the SD without disassembly.

A remix to fit the back of the Checkmate 1500 case, needs 2 M3 screws and bolt to panel mount it.

... a 3.5 inch slot. ...It is especially useful if used with IDE to SATA adapters as in the OG XBOX and some old-ish computers. ...If you open the model and it looks really small, scale it up to the following measurements: W: 101.3mm, H: 15.35mm L:121.5mm.

A simplified variant of @shawndw_ca's bracket - this has less fiddly bits, and the screw holes are reduced in diameter to allow for tapping with a suitable M3 die.

This version, have rounded corners, and 2mm hole for standard PC screw. ...

Made the cut-outs for the connector, jampers, CF slot. ... Added the stops for the PCB around the FDD connector.

Adapted from https://www.thingiverse.com/thing:3543297 to a low profile bracket.

My SATA adapter didn't fit so I made this remix. ... Printed in PET-G on bare glass, no adhesive, 0.28, 235/75, 20 lines brim Very good design for the original thanks for sharing :) v1_orig_secured is the original lid plus two screw holes for...

Based on clockspot's adapter, but reduced to fit 7mm hard drive cages. ...Made originally for a Toshiba Libretto 50.

I just did a quick tinkercad bad remix on the original to get it to fit correctly on my setup. ...I figured I may not be alone here so uploading for others