3d grayscale image

Note caution is warranted with the cooling impellers - the layer adhesion issues inherit to 3d prints makes it possible for the impellers to fracture under load. ...Wear eye protection and be mindful of risk when using TPU parts - Thrust Vector...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

Later edit: I have added a 20mm tall version i prefer the 25 because i can easily remove/insert the Neopixel and Det Plug for the 20mm version you will need M3x25mm instead of M3x30  Item Description: SKR Pico 4010 Fan MountThe SKR Pico 4010 Fan...

You will most likely have to do some sanding to get it to work smoothly. It is intentionally designed to be a bit tight due to the nature of 3D prints and how layer lines will wear over time. I'd rather it be rougher at first and smooth later than...

What you'll need: 3d printed parts- -Cuff (if your going with the premade attachments download both top cuff and bottom cuff) -Pegs (there should be 4 in one file) -Core -Lever -Dial -Ring -Base -Base connector -Pins (one of the two is specifically...

 READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

 (The combined slop of the 3D printed parts will give you roughly +/- 0.5mm of tolerance on your cut.If you buy hex on sites like Online Metals that sell in 12" increments, then each 12" will get you two cut hex rods. Preparing the JigThe jig has two...

On the bright side, all it requires is a 3D printer with no further effort to create.This remake, the Foťák Rail version 3, is much more flexible. For starters, the two holes for the 15 mm rails are now slightly larger, with a diameter of 15.3 mm. We...

(be careful and slow with this as you do not want to melt the plastic)Possible improvements to the model for advanced 3d modellers:A better guidance for led strips so you can make it perfectly even across the sides and perhaps also the edges.The...

If not, here is a good pair you can buy (local hardware store is the best option):...

Now that I do own a 3D printer, I went and created a nice and customizable planting pot to finally make use of that otherwise rather useless down-spout. \o/Since everyone's situation will be different and there does not seem to be a standard when it...

Please feel free to comment or contact me with ANY questions; I love helping out a fellow 3D printing enthusiast when I can...BTW, a big thanks goes to @designsbydave for supplying the mount essentials. IMPORTANT Note: Assembly OrderMake sure to...

At this point Robot5, which is essentially just a nozzle attached to a large robotic crane arm, would begin extruding the molten iron, like a 3d-printer, across the surface of an inflatable dome-mold, to create the roof-caps of our three rooms. each...

This is a completely new version of my original design (here: https://www.printables.com/model/145632-dslr-rig) without the cage and with fewer parts. Redesigned in SOLIDWORKS for higher precision.You will also need:15 mm aluminum or carbon rods...

Here is why you would want to do this:You get load cell probing, which gives you the best first layer performance I have ever experienced on a DIY 3D printer.You want to experiment with the Nextruder which has those big gears. Maybe with a klippers...

Description: A set of 3d printable parts to compactly combine two LRS-350 PSUs into a compact unit with optional voltage and current displays. I put this device together so i could consolidate the 10+ individual power bricks for each compute node in...

You also need skills in 3D printing with PA or another heat resistant material and you need to drill a few holes into the mounting plate according to the printable stencil of this thing. When talking about front and back, the front is the side of...

This 3D printable enclosure was designed to mitigate those issues by allowing the cable to be wound up compactly and attached directly to the back of the Steam Deck. Once attached, all you need is a small USB-C pigtail cable to connect the adapter...

After sanding, I applied a pretty thin coat of XTC-3D to smooth out any other issues, and then gave it a light sand after it had dried. After that, I applied a coat of sprayable primer so my paint would have a good surface to attach to.</p> <p>With...

Note: The G code files are set up to print with PETG material.2) Procure the commercial hardware from the parts list, M3 screws, square nuts, hex nuts, and 4mm OD x 2mm ID Teflon tubing (or re-use the existing buffer tubing).3) Cut the existing 10...

I couldn't find any already-made tool models for this job, so I thought I will make my own. It can also work with the bowden fittings on most 3D printer models, both on the extruder and the hotend side. These fittings often get stuck on my printers,...

Be carful that you fully overlap the original top part.3D Print:1* cap* innerRing* outerRing1* mainBody1* usbStickCase11* usbStickCase2These parts doesn't require support, but I printed them with a brim to secure them safly to the print bed. I...

The input data you provided seems to be a list of tuples, each representing a point in 3D space. The format is as follows: * The first element in the tuple represents the x-coordinate. * The second element represents the y-coordinate. * The third...

Some words in own interest: To model the ship in 3D was no easy task, in the CAD program it has over 1000 features and many time and effort was put in it. So please leave a like if you enjoy the photos, leave a make (and also a like) when you...

3D Printer :...

The mod uses a stock foam nose which can also be bought separately, a quad **2205 motor** (16x16mm screw hole distance on stand) plus 3x M2 screws and (optional) 8x 1mm insulating spacers, Everything else is 3D printed. Weights are given in...

The original VTOL build walkthrough video not including conversion to TVBS: https://youtu.be/8DG942hFIpE And a basic Ardupilot setup video (no TVBS info here): https://youtu.be/4e3JP7eEZIU Pease follow the Ardupilot docs here for the initial...

... off the printing time.   My PayPal tip jar: https://paypal.me/design8studio   Various LowRider 3 CNC remixes:LowRider 3 CNC Collection View all my models and remixes on Printables:Design8Studio 3D models *Amazon product links are affiliate links.

...Nails and 3D printed parts are cheap and easy to replace. 7.6mm fits best. Any nail with Ø6-7.8mm (8mm model) and a length of at least 15-20cm should work. I'll add a 6mm model for smaller nails but they may be to short or don't stick in the ground.

At this point Robot5, which is essentially just a nozzle attached to a large robotic crane arm, would begin extruding the molten iron, like a 3d-printer, across the surface of an inflatable dome-mold, to create the roof-caps of our three rooms. each...