3d filament extruder

Modification of the original K8400 vertex extruder is required to reduce spring pressure for printing flexible filament. ... This involves several key components: one M3 * 10 screw, one M6 * 50 screw, one M6 wing nut, and one M6 locknut are necessary...

I redesigned the flexi filament extruder with a sturdy cable management system. A sleek ring was integrated into the existing project, providing secure protection for the hotend cables. ...Using Tinkercad's powerful fusion tools, I combined the ring...

This enclosure houses a switch-based filament run-out sensor that sits atop the E3D Titan extruder. ...The switch utilized is as follows:...

... crafted for Sunhokey Prusa i3 with Chinese E3D clone replicas. To install fan mounting plates, you'll need to drill M4 threads onto X-axis bearings. Extruder and filament coolers will attach to the fans using just a few drops of superglue.

Just a quick and dirty swap on the ball to the back and extended it to line up with the new extruder location. Print the ball here: https://www.thingiverse.com/thing:3152549/files Print Settings Printer: MPSM Rafts: No Supports: No Resolution: .15...

This is a belt extruder that I made for my dual extruder printer and has a 1:4 reduction and is filament sensor compatible. This extruder should be compatible with any printer and should be a direct fit in a any 20x20 extrusion profile. I shared the...

Guiding the filament through stock Anet A8 Prusa I3 style 3D printers is crucial for optimal performance and results.

I purchased a dual gear extruder (bigtreetech, maybe?) and there isn't enough clearance for the pneumatic coupler on the filament input side to clear the z-axis screw. So...i designed and printed an alternative. It's sized to take a 6mm PTFE tube...

Extruder-mounted filament guide for Anet A8, a clever solution to the pesky issue of tangled cable chains. I designed and built it myself after experiencing frequent disruptions from errant filament snaking its way into the cable chain. This...

To address my main issue with the TOM, I tried an adjustable pressure and free-wheeling follower by printing the Shaputer modification of Jag's extruder filament drive. Though it was a step forward, the 1.75mm filament still fatigued and wrapped...

This is a custom version of the Bowden extruder and filament sensor holder by jalanjarosz - all credits go to him. I recently upgraded my Anet A8 to the AM8, but doing so caused issues with the original Bowden mount on the aluminum extrusions. To...

The filament guide is designed to simply snap onto the laser-cut plywood and direct the filament towards the extruder while keeping the spool low and off the printer's surface. The settings used for printing this design are PLA material, 0.2mm layer...

I reduced the width of the original design to avoid hitting the X carriage when moving in the Y direction. This will fit an Ender 5 with a direct extruder. Category: 3D Printer Parts

Here is a redesigned extruder block with smaller drive gear hole (11.8 mm instead of 13 mm), allowing for longer filament support between the drive gear and hot end so flexible filament won't get stuck in between. As I own a Makerbot Replicator 1...

When I used Klipper, the frantic extruder movements made me realize that the bowden tube moves in and out slightly with a M6 coupler. This M10 should fix that problem. While I was at it, I made the hole for the PTFE tube smaller to fit my 4mm tube...

The bracket does bend slightly however it has not been bad enough to warrant any concern as long as you are feeding from above the printer, the stock screws for the sensor should be able to thread themselves in to hold in place and short M3 machine...

You will need a base part from the original extruder, as well as separate parts to assemble the kit: * 1 x screw M3x10 * 1 x screw M4x10 * 1 x nut M4 * 1 x nut M3 The M3 screw and nut are used to secure the filament sensor. The M4 screw and nut are...

I discovered that after installing the X Chain, the extruder end consistently grabbed the filament, resulting in printed products with unwanted defects. To resolve this issue, I began using a spare cord to gently guide the filament towards the back...

I experienced issues with filament jamming where it entered the extruder on my Charlstruder, an improved version of the Wade extruder. After four to five hours of printing, the print wouldn't complete due to a jammed filament, wasting valuable...

I'm using the amazing extruder fan modification from user nicolaidiz (http://www.thingiverse.com/thing:2037833) as well as the X axis cable chain (http://www.thingiverse.com/thing:1905344), which means that I only had two screws left over to fit a...

Replacement part for FLSUN QQ-S extruder

For utilizing a dual extruder setup

I found a similar one in the past for the stock extruder, but I couldn't find one for the dual geared extruder that has the entry point taller on the z-axis. It requires a 608 bearing (I used a ZZ, but any other variant should work as well). I...

... Filament-Out Sensor Mount on Thingiverse. To help others replicate my design, I've included a Solidworks file and STL of the modified part - the rest of the extruder remains unchanged since I downloaded it near the end of 2017 from their GitHub.

The combination of the drive gear providing more force and an almost fully enclosed filament guide allows the printer to successfully extrude flexible material. These modifications have greatly improved both my print quality and success rate using...

[Français - English below] Mixage du guide à filament de FedorSosnin afin d'être installé sur le support de câble au niveau de l'extruder réalisé par K Sims. Le projet originel de FedorSosnin est accessible à cette adresse...

The Lyman Filament Extruder has undergone modifications in this version. Key features include a larger hot end with a 350-watt heater, an automatic timing system, fan ducting, modified sprockets, and a hopper with adjustable motor speed on the...

... caused by underextrusion), it will only break inside the nut, not the intended housing. I successfully used this guide on both the incoming and outgoing sides of my MK8 extruder and found it works flawlessly for keeping filament nicely guided.

Hi, this is last mod that I made to print flexible filament on my 3Drag extruder. I made version with little modification for original 3drag teflon hotend, 16,5mm diametre. ... Optimized for 0.2 layer print Video of build and timelapse test print ...

I facilitated the change of filament extruder with just a click.\nPrint Settings\nPrinter: Anycubic Prusa I3, my go-to model.\nRafts: Not necessary, I've got it covered.\nSupports: No problem, I can print without them.\nResolution: 0.1 millimeters,...