3d earrings

This is not something to 3D print, unless you should want a model for some reason. This is a concept for a DIY household air conditioning system, I have not built it! Concepts: -Is it possible to make a serviceable, reliable, cheap and...

GND should be handled in the ribbon connector. Print instructionsCategory: 3D Printer Accessories Summary I like that the Artillery printers come with an RGB LED on the hotend. It's a nice touch! But what if it could be... Brighter? And more...

It's indicated by a blue light, and can be ended sooner, by an additional press on the button.Range is chosen by moving the foot pedal back and forward, over the desired range.After the range is set, it is saved to EEPROM (so it's not power...

Prusa Firmware 3.9.0 (MK2S) for Arduino RAMPS 1.4 board In my github repository (https://github.com/cimoalpacino/Prusa-Firmware/tree/MK2S_3.9.0_RAMPS) you can find and download the source code of a working Prusa 3.9.0 firmware running on an...

I printed them at 20mm (4 hours or so,) but they look even better at 15mm.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction Use with your Armoured Shelter https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models  or carry with the Machina to their...

Violence is never more than a heartbeat away.Keep your vehicles fueled!Stay in the fight!No support requiredResize for smaller or larger use. Designed on...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Change if you are using something else (trying to use up what I bought a few months ago.)Use variable height to smooth out the curves on the light. Designed on...

Beim ChaosRun handelt es sich um ein kleines 3D gedrucktes LED Spiel für den kleinen oder großen Zeitvertreib und je nach Spiel für bis zu vier Spieler. Die Grundidee habe ich von hier übernommen: ...

It includes BL-Touch/3D-Touch support, filament runout detection and power loss resume - only functions from SDcard. The firmware.hex file is included. DISCLAIMER: If you are using the firmware.hex file you are doing it on your own risk, since...

... to change a few files to get this working. Those are the files I have added to the project.The remaining files are mostly from the Voron Switchwire / 1.8 / Trident / 2.4 STLs downloadable from https://www.vorondesign.com/Category: 3D Printer Parts

These tires fit on the Traxxas X-Maxx, which I think is an awesome RC truck:https://traxxas.com/products/landing/x-maxx/If you want tires that last a reasonable duration, here are links to Traxxas tires that will last far...

The tray should now slide into place.Installing Drawers/Trays under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will need to slide a “Rail Lock Upper” into place on the back of...

I wanted to wire tie the mount to the shelf (as I have done with the printers).The link below is to the USB cable.Amazon Basics USB 3.0 Extension Cable - A-Male to A-Female Adapter Cord - 3.3 Feet (1 Meter) -...

The gear end is the front.No supports are required.Superglue works best for gluing it together.Will scale easily if you want a larger or smaller...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

Dragon and Mosquito use the same length of PTFE tube which is why they share jig.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress. Shipping takes a while from China but quality is excellent and the prices are...

See “Large Binder Clip Tentacle Monster” below in connectors.Tentacle Rail Clip BaseThis Tentacle System base includes a clip that attaches to the T-Slots in the aluminum extrusions used in Prusa and other 3D printers. Used in combination with the...

My bot came with 410 mm Y rods, which is reflected in the Blender file, but this design should work on older printers with shorter rods (the original i3 had 330-335 mm Y rods). The .blend file depends on my standard parts/materials library, which can...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

I did not try to 3d print everything in plastic if metal or wood made more sense and was faster/stronger/easier and not cost prohibitive.  3D Printing is mostly used for the connections and exact positioning of tubing.Everything here is my own design...

If do you need to get the lock back off, the best way I found was to stick long allen keys into both of the lock's holes and then pinch them together to lever the lock slightly apart, which reduces the pressure enough that you can wedge a thin...

His diagrams and commentary on escapement efficiency were excellent, however. I only discovered this write up on escapement design after I'd finished, but it would also be a useful head start for anyone interested -...

What to print: Print these files: icarus-1.2.1-for-orbiter-1.5-normal.stl orbiter-1.5-dragon-mount-1.1.stl icarus-dial-holder-1.0.stl icarus-belt-peg-1.2.stl icarus-fan-duct-1.3.1.stl icarus-orbiter-1.5-dragon-and-mosquito-ptfe-cutting-jig-1.0.stl...

It appears to be a set of points in 3D space represented using an [Hull format](https://docs.python.org/3/library/pickle.html#pickling-hints). I will assume you'd like me to convert this into some kind of array. However, there are no "lines" or...

If you want to add time indicators to the watchface I'd recommend using roman or greek statues holding the numbers, to fit the theme. UPDATE: I've added a few statues with numbers to make reading the clock a little easier, they are based on the...

By doing so, I can now get more of the STLs to show up in 3D view on this site. The updated files have 10-18-23 dates and are renamed with "-remake" or "-k". 10-10-23 Update: Two items - Assembly Hints and Images added as a new section, and an...

... at 0.2 layer height.</p> <p>But once you've raised the limits, it's worth seeing what a 350mm/s travel move really looks like at 5500 or 6000 mm/s^2. (Answer: sorta scary, honestly) Designed from scratch in SketchUp. Category: 3D Printer Accessories