3d dongle

This is a straightforward holder for the OnePlus 6T audio adapter. ...It's best to print it with a flexible material.

Hi, I created this design for a buddy of mine who needed to install the USB adapter for his HyperX Cloud 2 headphones underneath his desk. ...This is my first time sharing one of my designs online, I hope you enjoy it!

I worked on the final case design for the GCMax project alongside Dan Kunz (Citrus3000PSI). For the latest revision of the GCPlug project, I took a fresh approach to the case. Rather than breaking it down into four separate pieces that attach with...

<p>Remixed the original design of Spavis as found here: <a href="https://www.thingiverse.com/thing:1326681">https://www.thingiverse.com/thing:1326681</a></p> <p>Credits to the original designer; I only increased the width of the ring a bit to give it...

An insert that fits in the cable slot of the MX Master 2 Heavy Duty Case by osxcar102030

The components include a Raspberry Pi Zero (W), a Micro USB T port Male plug, a Male USB to DIP connector, an 85 x 25 x 40mm Lipo Battery with 600mah capacity, a Lipo Powerbank module, and five 3 mm Neodymium magnets.

Inspired by this video yZkz_a52I6s And using the following components: Micro HDMI to HDMI connector B00CHSJOK0 and USB MicroB Plug 1826 one end of this USB cable 592 and USB MicroB Female Plug 1829

USB-C Audio Adapter Holder - Perfect Companion for Travelers and Organizers, Secure Closure with Magnetic Lid Safeguards Contents from Damage During Bag Storage.

I used the Hyper Tough Red wall anchors and Screws. The screws and anchors came is a multi size pack. ...I sized this wall mount for the following anchor and screws: Anchor: #6-#8 x 1-1/4 inch Red anchor Screw: #8 x 1-1/4 inch Philips Screw Here...

Compact iPhone accessory converts into a functional keychain attachment, securely holding your Apple headphones in place at all times.

I've designed this with 0.2mm tolerance as it works fine with My Ender 3 Pro config - printed this fine with and without raft at 0.2mm and 0.4 nozzle.

holds usb-mini usb cable for use with car mechanical analysis computer

Compact carrying case with a convenient keyring loop, designed to safeguard and transport USB-C adapters like the Luna Display adapter shown.

We're bringing back the classic look with a modern twist by incorporating an intricately engraved steam logo into our design. The iconic logo now takes center stage, its presence felt throughout every aspect of the design. ...This subtle yet striking...

Nintendo Switch Wall Mount Dock for Generic USB C to HDMI Adapter. Make sure to use a Nintendo branded charger with the HDMI adapter! This allows for removal of the adapter to bring it along. The adapter can be inserted both in left and right...

GIMX makes it possible to share peripherals across multiple gaming platforms. To do so, you'll need a specialized adapter like this one (atmega32u4) and a compatible computer such as a Raspberry PI3, PC, or any other device that supports the GIMX...

a little help to fix the key under a shelf with two countersunk screws, max diameter 4.5mm, the key fits on one side with the USB connector and is held in place once the antenna is screwed.

Just a simple wall mount for the stick.

Just a simple wall mount for the stick.

Simple remix of the Brawler64 support to fit the Admiral controller.

This developer created a compact debugging tool specifically for STM32 microcontrollers. ...The project can be found at the link below: http://e.pavlin.si/2016/02/22/st-link-v2-on-a-single-sided-diy-pcb/

Printing does not require supports. ... Hardware: Four round 4mm x 4mm neodymium magnets

<p>This is the final case design for the GCMax project that I worked on with Dan Kunz (Citrus3000PSI)</p> <p>I decided to take the a new approach on the case for the latest revision of the GCPlug project. ...Rather than having 4 separate pieces which...

I remixed the original design of Spavis, found here: https://www.thingiverse.com/thing:1326681. Credits go to the original designer; I simply widened the ring slightly to give it more strength. ...This design fits perfectly with these converters:...

<p>I've designed this with 0.2mm tolerance as it works fine with My Ender 3 Pro config - printed this fine with and without raft at 0.2mm and 0.4 nozzle.</p> Category: Other

I decided to reuse an old USB connector from a DVB-T stick instead of gluing mine or buying a new interface PCB. I simply soldered it directly to the ground pads of the unmounted connector, and voila! A quick fix. The pads on that unmounted...

I remixed the original case uploaded by kapakahi from Thingiverse (https://www.thingiverse.com/thing:2467428) to fit a larger USB connector. Recently, I ordered these USB charger cables on Amazon and discovered that the connector was bigger than...

This is a simple wall mount for a Sonoff Zigbee 3.0 stick. ...Use adhesive pads to stick it to the wall and then the adapter itself can be clipped into (and out of) it easily.

Customized version of https://www.thingiverse.com/thing:3715970 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3715970