3d dinosaur model

Tonight, I finally decided to model the hinges in fusion and print out new ones. The test seems to work well enough. So I'm printing them with a roll of ProtoPasta Carbon FIber HTLPA. This will be my first real test of this filament. I will update...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

I have no model or figure of Buffaloman in a camo tank top. The bazooka is actually pointing backwards to simply be held resting on his shoulder. I scaled it to 40% and positioned it to be resting between two shoulder spikes with the hand grip...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

If you want to save time while testing, you can print the included calibration test instead of the full model, but that is optional.Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It may feel...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

It Lets You See Your Model Being Built and Doesn't Obscure View. Why Make Yet Another Cooler? Cooling Plastic Just After Its Been Extruded Is Essential on FDM Printers and There Is a Lot of Choice for Cooling on the Makerbot Clones. I Tried All of...

Print Settings Printer: FlashForge Rafts: No Supports: No Resolution: .2mm (Medium) Infill: 20% Doesn't matter Notes: For the most part, I intended these to print without supports; however, the housing is so wiggly that it needed some once I...

For other projects and creations, please visit my Instagram page (https://www.instagram.com/roger.egli/) or check out my YouTube playlists for model/machining hobbies (https://www.youtube.com/user/MrZhefish/playlists). Hope you find this mod...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

The firmware numbers will match regardless of your printer model. If you use a slicer that requires EEPROM, make sure to update your EEPROM settings to match your new firmware. The easiest part is printing the adapter plate - any ABS or PLA preset...

This is a stepper motor-controlled model turntable designed for 009 but compatible with short N gauge locos (loose the fences). The bed is 100mm long, and the Arduino code will follow in the coming weeks. Primarily designed for DCC++ JMRI CMRI...

It's also compatible with the Chinese clones of both these models, often referred to as "J-head" extruders. There is a cable guide built into the design which will assist with keeping everything tidy and reduce any stress on the heater and thermistor...

Here you find better resolution for the pictures: https://www.printables.com/de/model/501107-led-rgb-matrix-ws2812b-esp32-wled-32x32-round-squa https://www.youtube.com/watch?v=5lFdzL06OOs On Youtube there are lots of tutorials to build a 32x32...

**Update October 26, 2017:** Since I was messing around with the model anyway, I figured it was time to do something I've wanted to do for a while. To decrease the "stack height" on top of my inexpensive flexy tripod, I slapped an 18.5mm ball clamp...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

I have since printed out another model in ABS which I am hoping will be more durable. PETG would be another more durable substrate to consider using. Special thanks to Jim Harmon at Keystone College and Emmitt Zugar at Salem Community College for...

... you'd like to copy it into your workspace and mess with it. [Buy me a coffee :)](https://www.buymeacoffee.com/jcolega) - [Printables](https://www.printables.com/model/152611-lego-vehicle-wall-hangers) - [Thangs](https://social.thangs.com/m/65559)

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

I simply used a couple of dabs of model car glue, but you can use epoxy if you prefer. I would avoid CA because the fumes may fog up the inside of the lens. The finished part is shown in "modified camera.jpg." I just checked Amazon and found that I...

I decided to use them because they are improved and updated compared to the older ones.The parts of the X axis are those of the MK3S model. Hi there!I've been looking for some time already printable Prusa parts, adapted for IGUS bearings...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Modeled after a 1915 candlestick phone, early versions had no dial because you just lifted the earpiece and clicked the lever a few times to get the operator's attention and told her the number or person you wanted to speak to. This is a fairly good...

 Some require the models to be rotated so that they share space with their neighbors.AssemblyEach tray is comprised of 4 (or 5) rows.  Each row comes in two parts (so they fit on smaller printers like the Prusa Mini) and need to be glued...

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

I used this here: https://de.banggood.com/Remo-B5509-Ball-Bearings-593mm-For-1621-1625-1631-1635-1651-1655-RC-Vehicle-Models-p-1450586.html - 9x M3 30mm screws and nuts to conetc top and bottom trays - otionally: 9x M3 0.5mm washers to put between...

If you do this, use the "Pusher Extd" model. To modify the solenoid: 1. Remove plunger. Remove about 3mm of the black base and sand flush with the metal slug. Sand the black base to make it slightly thinner if you want to add an additional spring...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

... clean it up.  Pictured below are the on edge views of the dove tale design and the individual prints used in the above picture.If you decide to model your socket or light switch cover, the dove tail profile I used is shown below (units in mm).