3d concentric circles

 Failure to remove this will not allow the fan to snap into place and mount correctly.Parts List:Fans:  https://a.co/d/7E1LBpB3D Printer 24 Volt Fans Blower Turbine Turbo Dual Ball Bearing, Brushless Cooling 50mmx15mm 2PIN (Pack of...

SAFETY The big question that many people will have is the most obvious one - Is it safe to hold a powered saw blade with a 3D-printed clamp? Well I guess that depends on the level of use and abuse that the tool gets subjected to, but consider that...

If there are any errors or you have requests for special changes to design, please let me know in the comments. All pieces are support free!Let's start with the list of parts you will need to complete the project:3D printed parts (See...

The alternate roof is 2 separate 3D print, use the layer change details above to get correct colours. ###Step 4: Exterior & Interior Props (Optional) All the exterior and interior props are optional. The parts found in both folder are simple...

For those who are new to 3D printing, I suggest using the project files for the knobs. I have included supports in the hex pockets. Without them you may have problems getting the heads of the bolts to seat down inside properly. If they are not seated...

I do not own a BL Touch so this design was based on 3D models so definitely WIP. I have increased the thickness of the Duct mount to the base unit to make it even more robust on the LH duct. You may now need to use M3 x 10 mm to fix to the base unit....

I plan to improve the mount from your feedback as well as from my own observations when using it.Toolless accessory mountThis mount allows you to attach custom addons to your 3D printer with toolless operation for adding additional functionality to...

All of the above along with unfinished cooling duct of the cyberfooks1 design caused me to decide to try my own skills to make a plate for Hemera for Tronxy X5SA Pro, addressing all above issues, adding a bit of rigidity and tuning everything to be...

When printed in flexible filament, the tire should be relatively easy to put on the wheel, yet will "snap" into place and not come off too easily. Trap those pennies! I love designing "impossible" things for my 3D printer. One thing that truly...

All the rails have been rotated so that they are easier to view & distinguish at a glance when using the 3D viewer. The clicky variants have a modified groove so that when they stop, they remain in contact with the gear with just enough friction...

This is a completely new version of my original design (here: https://www.printables.com/model/145632-dslr-rig) without the cage and with fewer parts. Redesigned in SOLIDWORKS for higher precision.You will also need:15 mm aluminum or carbon rods...

Check out my profile for a full list of my designs._________________________________________________________________________________If you found this design useful and want to support me in my 3D printing and photography endeavors, check out my...

7 - All items in the console are 3D printed, optional decals are attached to the sides of the model. A JPG file containing the decals is included in the pictures section. 8 - Small note: the back_wheel_attachment/left/right might have a few small...

Because of this I figured it would be nice to dig up the old 2D drawings and turn them into a 3D model so you can print your own Fauvet Girel and motorize it with relatively little effort. I also provided parts for a dummy model in case you want to...

#IKEA Lack Enclosure# ##for 50x50cm / 25x50cm side panels## ###Why another design### I liked IKEA Lack Enclosure for 3D printer, so I bought the IKEA tables and acrylic glass of standard dimensions 50x50cm and 25x50cm (4mm thickness), but I didn't...

Violence is never more than a heartbeat away.Use those guns! Deliver your cargo!Stay in the fight!Small painted-on supports are required for Gun overhang and Freight Ten gun mounts (Support Enforcers Only.)Glue gun mount onto the Cab (see...

https://www.prusaprinters.org/prints/22008-double-stack-ikea-lack-enclosure-v2-works-w-mmu2s Print instructionsCategory: 3D Printing It works really well!!! Saves time, space and helps dry filament Saves Space: The universal auto spool rewinder saves...

... also facing the spool. Tighten the second spool holder until it grips the spool. Next, lock the spool holder onto the shaft by threading the locknut STL onto the shaft and tightening it until everything is secure. Category: 3D Printer Accessories

* Once assembled my new FelFil extruder (https://cults3d.com/en/3d-model/tool/felfil-evo-extruder-case) I began to design a cheap and affordable spool winder; I had to design a cooler for extruded filament and a digital sensor for filament diameter.

... <ul> <li>Now connect all 3 pieces of pipe (26.5 cm)</li> <li>Cement them, make sure the length are the same when glued. Try without cement first and to test and then cement. The result should look like the image bellow. Category: 3D Printers

... Print Settings Printer: Folgertech FT-5 Rafts: No Supports: No Resolution: 250mm or less Infill: 30% Notes: Three bottom layers, three top layers. How I Designed This Designed in Fusion 360 Category: 3D Printer Parts

Note the treads match in shape the body of the Freight Ten.Superglue the cab to the body to the front grill is overhanging the front slightly (see the images).There are extra parts you can print (road wheels, treads, etc.) to add to the model.No...

&nbsp;And then I used water-based washes to give it a weathered look.&nbsp;Here’s an assembly video:&nbsp;&nbsp;Complete the set!!If you're bounty hunting, you should download my badge design and some bounty hunter tokens to give to helpful Galaxy's...

(I found that setting extruders using the Part tree on the right instead of using the 3D view didn't actually cause the colour to change!).Use the vertical split tool to split the model at 250mm, and keep both upper and lower parts. Select the longer...

There are configurable-text-based creations, multi-line label, gadget display stand, sweeping name plate, bunting banner, customizable text box III, pyramid text, name plate, Customizable text box with lid and round text. Have also a look at my...

Use either a standard or nyloc M3/6-32 SAE nut and screw tight.Assemble the remainder of the printer per the instructions in Prusa's repository: https://github.com/josefprusa/Prusa3/blob/master/doc/manual.txtOpen Source Hardware STL courtesy:...

Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ Previous version here: https://www.thingiverse.com/thing:4650517 As per the previous version a big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken...

---------- # STP FILES Again I included the STP files, so that everybody with a decent 3D CAD can load the volume models. ### The thread test STP In this file you find a test screw (with the nominal threads) which is identical to the spindle...

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. ...Scan the World is...

This a rover platform that you can assemble choosing among manyblocks that fit in the samemounting points, so you can adapt the design to what ever fits your needs the better. NOTE: You can find the main page of the project, with the index of related...