3d catfish

Theres is 9 parts printed in 3D, all in PLA. Thank's to HaikuFPV for the inspiration (https://www.thingiverse.com/thing:1410967). Try to use Tough PLA, like APLA+ if you can. ABS and other "hard" materials will work as well. Supports are...

- 3D Printing is about beauty and design. When storing the filaments visibly, the storage should at least satisfy some degree of beauty. When designing parts to be printed, you also need to take care of the print process: - The print...

Violence is never more than a heartbeat away.Keep your vehicles fueled!Stay in the fight!No support requiredResize for smaller or larger use. Designed on...

3d.) Use razor blade to clean up hole and surface (to make surface flat) 3e.) Remove all leftover magnet pieces blocking screw head. 3f.) Carefully clip zip ties holding bed wires to carriage. DO NOT clip wire (Obviously) 3g.) Remove four bed...

These tires fit on the Traxxas X-Maxx, which I think is an awesome RC truck:https://traxxas.com/products/landing/x-maxx/If you want tires that last a reasonable duration, here are links to Traxxas tires that will last far...

... you shouldn't feel any escaping air around the unit when it's running. Enjoy! How I Designed This Designed from scratch in Sketchup, with a lot of reading about compressor fan designs online but no actual math done. Category: 3D Printer Accessories

Feel free to do whatever you want with them.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

For hell's coming in the “White Desert.”Print one "left base" and one “right base.”Print “left side with balcony,” “middle,” and “right side with balcony.”Print as many floor as you choose.Print 3X of the “roof.”Stackable for reconfiguration or super...

See the bundled "Using OpenSCAD customizer" PDF for more details.Recycling symbol offset: An extra thickening (positive offset) or thinning (negative offset) of all the symbol, to aid in 3D printing. Usually you won't need to add any value, unless...

Average those two altitudes, to get your result (we rotate and average to cancel out any errors due to the ring not hanging perfectly straight).Avoid windy days if you can't move out of the wind, as the ring blowing around reduces accuracy...

... once you have confirmed it's done. You will see just bars on the display only.</p> <p>After that load what ever Firmware you like be it 1.1.9 or 2.0. This will give you a fully clean install, with no hang overs from past FW. Category: 3D Printers

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

The remaining Yeallow (G32, SDA) and white (G33, SCL) cables were soldered to the corresponding pins on the PCD, to connect them to the sensor module...

Take what's theirs and make it your own! More Armour!Demolior Class Heavy Tank - https://www.printables.com/model/135967-tank-demolior-class-heavy-deathhead-ii-model-scien Scopulus Class Heavy Tank -...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Note the treads match in shape the body of the Freight Ten.Superglue the cab superstructure to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did...

Also see my component compatible Chonky Jarhead Priest: https://cults3d.com/en/3d-model/game/modular-chonky-jarhead-priest The builder allows you to build ranged Chonky Jarheads, including heavy weapons, as well as melee Chonky Jarheads with many...

Use with your narrative in the hive or megalopolises of your wargaming environs.Print with “Fill Pattern” as "Adaptive Cubic" to save time and filament.No supports are required.Printed at .20mm Quality.Takes a little under 2 hours to print.Designed...

Hi, recently I built a Crack Laser and decided that I would experiment with 3D printing some better hardware. This equipment trades an extra approximately 5 grams to the build for zero slop linkages that reinforce the hinge at the control horn too. ...

This could be imported into a 3D program to manually add some text, symbol(s), or whatever.Stamp 1 Rubber Blank with Border.stl: Same as Blank but with a border.Stamp 1 Rubber Blank 4mm.stl: Same as Blank but 4mm thick (vs. 2mm).</li><li><code>Stamp...

Game Tokens - large and small!&nbsp;&nbsp;For use in your next wargame!No supports are required.Grooved backside to facilitate easy grip even when soaked in the blood of your enemies.Plain-backed version for those unconcerned with being soaked in the...

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

Change if you are using something else (trying to use up what I bought a few months ago.)Use variable height to smooth out the curves on the light.&nbsp;Designed on...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;...

Align top frame width from the 200x400 sheet slots if needed.Mark screw locations on the top frame, drill and install screws (M3x16)Add metal rod pieces to the hinge between top frame and front sheetGlue magnets to 28 SL1S enclosure front bottom mid...

The tray should now slide into place.Installing Drawers/Trays under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will need to slide a “Rail Lock Upper” into place on the back of...

I printed them at 20mm (4 hours or so,) but they look even better at 15mm.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

Use for scatter terrain, on your model railroad, in a diorama, or whatever gets your motor running.Two sizes are included within the files.&nbsp;No support required.Easily resized.Assemble: super glue the top frame to the posts.&nbsp;Designed on...

Much of that comes from off world crates.Build!&nbsp;Get back in the Fight!Designed on Tinkercad.There are seven parts to assemble on the Attack Recovery Vessels.Four sizes - large to small.Lumber stackFour pieces of loose lumberStack or glue, make a...