3d blinds

More cargo for all of you Sci Fy tread heads out there.Freight Ten https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction Transport your Armoured Shelter...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                      

It's indicated by a blue light, and can be ended sooner, by an additional press on the button.Range is chosen by moving the foot pedal back and forward, over the desired range.After the range is set, it is saved to EEPROM (so it's not power...

Keep your stuff from falling out.BullNose Freight Ten: https://www.prusaprinters.org/prints/143750-freight-ten-bullnose-model-science-fictionSingle Cab Freight Ten:...

3D Printing is about beauty and design. When storing the filaments visibly, the storage should at least satisfy some degree of beauty. When designing parts to be printed, you also need to take care of the print process: The print should use as less...

Change if you are using something else (trying to use up what I bought a few months ago.)Use variable height to smooth out the curves on the light.&nbsp;Designed on...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

In my experience the sports ball inflation needle runs cooler - but wears out quicker and is more likely to deflect in use and cost accuracy. Because the guide can get warm from the friction of the needle running inside of it it's best to use a heat...

Now slide out the belts out the back of their mounting slits and you can take the plate with the two attached upper V-rollers of the printer.Also unscrew the the top two bolts and put them back in with the 3d printed mounting plate sandwiched between...

Also this shape is very special because you can use two V Plate and invert one to create a sort of "wave" that visually connect two I plate that is place up and down.Double C Plate* : This isn't a stand alone plate, this mean this plate is useless on...

Here you are!Designed for use with “Way Basics Eco Stackable Storage Cube, Cubby Organizer (Tool-Free Assembly and Uniquely Crafted from Sustainable Non Toxic zBoard paperboard), White”...

GND should be handled in the ribbon connector. Print instructionsCategory: 3D Printer Accessories Summary I like that the Artillery printers come with an RGB LED on the hotend. It's a nice touch! But what if it could be... Brighter? And more...

For the majority of items, the mesh origin has been set so that when you import these objects into your 3d editor of choice, they are positioned as they would be on the sample ships provided. When comparing parts, especially wings, you’ll notice a...

... <p>Added Dock-V1.1: uses far less resin than Dock-V1 (Update untested and not included in the step file)</p> <p>Added Duct V-1.1: More consistent refill behavior. Keeps the resin level more steadily than V1 Category: 3D Printer Parts

Don't let them destroy your home.&nbsp;Build!&nbsp;Get back in the Fight!&nbsp;Designed on Tinkercad.Two sizes - Large and Small.Stack for use or glue.The buildings are stackable; use the girder frame at the top.Make a large building or small.Print...

Much of that comes from off world crates.Build!&nbsp;Get back in the Fight!Designed on Tinkercad.There are seven parts to assemble on the Attack Recovery Vessels.Four sizes - large to small.Lumber stackFour pieces of loose lumberStack or glue, make a...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                          

Theres is 9 parts printed in 3D, all in PLA. Thank's to HaikuFPV for the inspiration (https://www.thingiverse.com/thing:1410967). Try to use Tough PLA, like APLA+ if you can. ABS and other "hard" materials will work as well. Supports are...

A steel axle would be overkill but a 3D printed one is replaced in minutes and you can use anything with a diameter of 5mm as an axle.Tighter construction -&gt; less wiggling of the parts. Feels sturdy.</li><li><strong>No need for support</strong> in...

... once you have confirmed it's done. You will see just bars on the display only.</p> <p>After that load what ever Firmware you like be it 1.1.9 or 2.0. This will give you a fully clean install, with no hang overs from past FW. Category: 3D Printers

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

Game Tokens - large and small!&nbsp;&nbsp;For use in your next wargame!No supports are required.Grooved backside to facilitate easy grip even when soaked in the blood of your enemies.Plain-backed version for those unconcerned with being soaked in the...

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

There is now an uploaded drilling guide that takes that into account. Update 8: The long awaited instructions document is now uploaded! Update 9, uploaded an updated Taz 6 specific endplate. There are several other related projects that are...

Violence is never more than a heartbeat away.Keep your vehicles fueled!Stay in the fight!No support requiredResize for smaller or larger use.&nbsp;Designed on...

I made them on TinkerCad.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

Note the treads match in shape the body of the Freight Ten.Superglue the cab superstructure to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did...

The tray should now slide into place.Installing Drawers/Trays under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will need to slide a “Rail Lock Upper” into place on the back of...

Use for scatter terrain, on your model railroad, in a diorama, or whatever gets your motor running.Two sizes are included within the files.&nbsp;A small area of the power turbine need supports (see images).Easily resized.&nbsp;Designed on...