3d atom models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Sincethis design is compatible with a whole variety of lampshades, be aware that somelampshades will have to be scaled down or up to fit the base's default settings. Base- Layer height: up to 0.3mm is fine, there's little detail on the Z-axis-...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

I have designed myself some shelves for the paints I use with my Warhammer 40K and other model painting. The system is designed so you can put a shelf on both sides of a wall and chain them together. For instance, you can do a 2-step wall, shelves,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 7 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 0 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

As with all of my parts, these are modeled after real-world tools, ideas, and measurements using a caliper, feeler gauges, and other tools. Custom Section Objectives The usage of this part will provide the student with a method to replicate...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

But the base design is a mix of: Ichibey's Sakura CoreCube Hbot modeling work Jetguy's lasercutter templates and electrical / extruder configuration DNewman's Sailfish programming for CoreXY gantries Credit should go to the above -- I'm just...

That link also calls for using alanho's file to hold the TFT50, here is a direct link to his page as well: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/alanho/BTT_PITFT50_v2_Mount I also made some simple changes such that it...

Refer to the pin diagram below.Connect the SMPS OUT- to a ground pin on the RPi.If you're using the fan, install it on the lid.Connect the fan's power and ground wires to pins on the RPi. My 5v fan was a little on the loud side so I used 3.3v and...

The COMPLETE The Bloodhunt bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Bloodhunt Knights were the first Soulless Vampire troops to be sent to the mortal lands of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

**HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE** -------------------------------------------------------------------------------------- Here are the two videos that give details on how I print much faster with stock hardware (changes to slicer...

:D This is a "small" and simple attempt to build a 3d printer. Small and simple are the keywords here. Just some basic parts to print, standard components you can get anywhere and no special and expensive tools required, as I don´t have access to a...

My goal was to make as many of the modifications as possible to be 3D printed parts.Note that in addition to the .STL files, the Fusion 360 file containing all these parts is also provided. Some parts need to be rotated after importing into the...

Basic profile: 25% infill, 4 walls, ironing top layers, ...Note: the included images illustrate the goals of the steps outlined below.[ ] 3D Print included stl files[ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan...

3D Printing: The Morse writer telegraph consists of many printed parts that are assembled together. Some of them could have been printed as a single piece. However, I avoided doing so to keep the printing times manageable. Additionally, this allows...

The only sound comes from the layer fan.I have included the STEP files to facilitate remixes and alternative configurations.An associated BMG type extruder/carriage can be found here:...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...