38 drill bit 3d models

The phone holder hangs just below the headrest, and it will be off-center a bit in a direction, depending on which rod you hook it on. It fits all car headrest bars, from 10mm to 14 mm.MPH carheadrest frictionfit (down)MPH carheadrest frictionfit...

Please try at first which one fits best for you 02.08.2016 Modified the tow-bar a little bit and added another part for connecting the trailer to the rover http://www.thingiverse.com/thing:1700138 Added a new link to the 6802zz bearings Added a...

Cut the BMS wires to size so that the wire can reach the corresponding 1x2 slot you left blank with a bit of slack so that the wire can run down the side of the battery, then wrap over the edge printed side piece along the batteries over to the...

The fact that he can’t stop smiling doesn’t bother him one bit, but he’s still protective of his teeth. Don’t let him catch you wearing a shark tooth necklace. "Legs" Sully Clawford Even before his transformation into a carapaced titan, Sully had...

VLC can do this, but it's a bit finicky to set up. It's in: Advanced preferences > Filters > Scene video filter. Then the filter has to be configured, and VLC needs to restart. And you have to remember to turn it off, or it will keep extracting...

There are also useful coat hangers and finger toys.Or just check out all my creations.By the way, the quote "Whatever it is, I'm against it." is from a song by Groucho Marx in the movie 'Horse Feathers'.Thanks go out to constantmotion, DynoCZ,...

Libre à vous de les écouter pendant que vous jouez. 3D Zoetrope convertible in praxinoscope A bit of history:The zoetrope is an optical toy from the 19th century, precursor of cinema. It is a drum (cylinder) inside which is placed a...

Updated the stator bowl to fix supports not properly generating Updated 10/15/2020, McBoatface 2212 motor mount was a bit of a tight fit, adjusted motor mount. Adjusted joints between sections Updated 10/16/2020, added receiver tray and antenna...

240x500mm1 Frosted acrylic hex lid or other material of choicetop lid does not need to be translucent1 Assembly guideToolsI strongly recommend a 90 degrees drill adapter or a ratchet driver to be able to access the screw from within the Hex...

5.2 Memory Hardware Requirements When we start to think of storing any appreciable fraction of a technical literature in computer memory, we run into billions of bits and, unless things change markedly, billions of dollars. The first thing to...

It is a bit larger than the Moon. By its proximity to the star and the small size it is likely to be rocky in composition, like the moon, but the exact composition is unknown yet because the mass and density of any planet of the system cannot be...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...

It has nothing to do with the real Earth's Moon1; in the book, it is a planetoid, a bit bigger than Mars, that suddenly appeared in the same place and orbit of the real counterpart, replacing it, and causing disasters on Earth after its huge tidal...

Wings may not fit within their holes, you would need to sand the joint a bit. 1:350. 22cm long. The same conditions as the previous one.</li> <li><b>1:200</b>. 38cm long. Scaled 80% of the 1:160 scale pieces.</li> <li><b>1:160</b>. 48cm long. Each...

I add nothing but a reshape of the original model, it's not more accurate, just a bit nicer when printed. I also divided the model in 2 and 4 parts: the lobes are tagged as "north" and "south", which are the NW and SE lobes, based on their...