357 sig vs 9mm 3d models

I am not advocating one over the other (straight vs 2 degree canter), I have tried both to see if there is a difference. Thanks to sparticus1701 for doing the original template, if you are just interested in the straight template, please go see...

-- THE CABLE WINDER II -- This design is an updated and improved version of my popular design “Charger Cable Organizer”Thanks to all that posted feedback and makes of my other design, and as a result of all your suggestions and ideas for...

(physics) Discussion of involute vs. cycloidal gear tooth profiles. (CAD, intro engineering)</p> <p>University:</p> </li> <li><p>Calculate the stresses in the frame pieces (modelled as a pin-connected truss and with moment connections) (statics)</p>...

Super Glue on PLA/PLA+ vs. PETG ----------------------------------------------- If you print on PLA or PLA+ the super glue should hold well enough that the print will break before the bond breaks...however, the small clips will be more likely to...

voltage (see below)How to choose the right Ballast resistor for the LEDIf you buy recommended LED from the BOM, parameters for formula are:&nbsp;V_LED (forward voltage) = 2.5 VI_LED (forward current) = 20 mA.Example: When your Source Voltage has...

Double vs Single: It is not possible for a single pawn to "hit" a double. A player cannot move his single pawn to the same square as an opponent's double. A player cannot move past an opponent's double for 1 move. However, a double can "hit" a single...

As for the Data/Sig-line I usually use D4/GPIO02 on the Wemos D1 Mini. Hence, solder a not too thick cable to that GPIO.And you might want to flash your microcontroller before you put it all together. Don't forget about it. Once flashed, I usually do...

The end of the jumper with the Dupont connector now needs pushing onto pin No:19 which is GPIO sig 10 where the Neopixels will get their data signal from. See the photo for a bit of a clue. (If you hold the Pi with the GPIO pins to the lower right,...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 30 mirror = No shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

The model’s chosen scale is 1/8 for the FDM version and 1/16 for the DLP/SLA/SLS version.FFF/FDM version dimensions:A printed model is 357 mm tall, 359 mm wide, 325 mm deep;DLP/SLA/​SLS version dimensions:A printed model is 179 mm tall, 178 mm wide,...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

This diorama shows the final battle between Major Dutch and this creature, also called Yautja.ABOUT THIS 3D FIGURINEThis figurine is the second part of Diorama "Dutch vs Predator". The model is saved in STL files, a format supported by most 3D...

 This applies the scarf seam only when a round surface (vs sharp corner) is encountered and blends the best of both worlds.  You can also adjust the threshold angle which determines the crossover point between traditional and scarf seams.  In my pot...

HOW TO CHECK: Just unplug the cartridge and thermsitor plugs on the extension board, use a multimeter in diode mode and check the metal hotend vs. every line of the wiring. HOTEND IMPROVEMENT: Heater cartridge: The heater cartridge wires need to be...

This model is a part of the diorama of the last battle between the Predator and Major Dutch.ABOUT THIS 3D FIGURINEThis figurine is the first part of Diorama "Dutch vs Predator". The model is saved in STL files, a format supported by most 3D...

... and pump jet. Updated water cooling stator bowl, uses embedded nut for more secure water nipple retention. Note water cooling is now intended to passively exit vs being pulled by pump jet (if this is insufficient let me know and I might revisit)

This can be done with a breadboard to avoid soldering; using the perf board.Here is the Arduino...

ABOUT THIS 3D MODELThe USS Sulaco is a fictional spacecraft that appears within Alien vs. Predator universe, namely was an important setting in the course of 1986 American sci-fi film ‘Aliens’. Aside from being a troop transport ship,...

&nbsp;Experimenting with 3 and 4 perimeters (vs 2) has demonstrated there is benefit to eliminating some of the flex in the tower pieces.I recommend you print the&nbsp;156DT_shaft_Base_double_wedge_Pin.stl&nbsp;with at least two additional perimeters...

I have placed the parts in the best orientation possible with surface finish and part strength in mind.&nbsp;The legs have a really bad hight vs. base area ratio which makes them prone to breaking away from the build plate.<strong>I added a...

The lid style (inset with notches vs cap lid) can also be changed. Lids Fitting - If the lids are too loose or too tight, there's a commented out parameter to change it. Finger Cutouts - I added finger cutouts to reduce weight, though it makes some...

Ideally the part should be installed so the inner flat faces are to the sides, which will put the layers in a vertical plane oriented along the part for maximum strength vs. gravity. There should be plenty of clearance, though you might need to shave...

Important note: The connector for the potentiometer knob should be mounted upside down when attached to the control board (vs the original assembly instructions). If you don't do this, the servo arm will move in the opposite direction you expect when...