350 chevy power steering bracket 3d models

Bracket Required for Installation of Mean Well LRS-350-12 Power Supply The LRS-350-12 is a 350-Watt DC-DC converter from Mean Well, designed to provide reliable and efficient power conversion in various applications. To ensure safe and proper...

This is a wiring bracket intended to clean up the power connections to the battery in your vehicle. The bracket is designed to fit in the sliver of space available next to truck mounted batteries. It could also be used for tight spaces near front...

I redesigned the Basic Meanwell LRS-350-12 Power Supply Cover to eliminate the need for a screwdriver, as my enclosure makes it hard to access the side of the PSU. This redesign resulted in raised bumps to create a snug pressure fit and a cross-bar...

Construct a computer without a traditional case by holding the power push button in its bracket. When building a computer with just the motherboard mounted on a board, such as when creating a cryptocurrency miner, wires run rampant everywhere.

I Built a Simple Hooked Bracket to Keep Our Power Strip Off the Floor Without Drilling Holes in the Wall. It's Hanging from My Radiator's Cold Water Return. Print Settings: Printer: Multec M420 Rafts: No Supports: No Resolution: 0.4mm Infill: 6%...

The original switch is no longer made, but a replacement switch is available (see: https://www.conrad.com/p/pwl-2p1tl-6sasha-power-switch-pushbutton-switch-250-v-ac-6-a-2-x-offon-latch-1-pcs-701606). Because the replacement switch has slightly...

but I like the idea with the two corner brackets only and it works just fine for now.I just quickly changed the height from 35mm to 40mm, added a round cutout to not block the sockets / power switch, and printed 2 of these with PLA (no fitting PETG...

... size. The power supply is the Neewer 48v Phantom Power Supply. It can be found here: https://www.amazon.ca/Neewer-1-Channel-Microphone-Condenser-Recording/dp/B014H8AWGC/ref=sr_1_1?ie=UTF8&qid=1487390060&sr=8-1&keywords=neewer+phantom+power+supply

Quick and dirty bracket designed for hanging larger power bricks used, such as the Printrbot Simple. Originally intended for the power brick I bought to supply power to my under-cabinet LED lighting. That brick, like the one used by my Printrbot...

A Simple Bracket for SFX Power Supplies. It Can Be Used in Two Orientations on a STEGO BOARD 400. To Mount Your SFX Power Supply, First Apply Glue to the Insides of the Support Holes and the Small Ridges Nearby. Next, Center the Stems and Place Them...

On the first version I've used 2 existent models to create my Bench Power Supply:1 - https://www.thingiverse.com/thing:24672372 - http://www.thingiverse.com/thing:2897335Edit 30/March/2024: On this version, I did the model from scratch with a...

Wall Mount Power Strip

... for a longer one and so give the colums a lower rake. Unfortunately the orignal bracket it fixed with two shear-bolts so dismantling can be a bit difficult. Always loosen the brackets holding the steering rack so that it can move with the column.

Continuing to organize my workspace, I decided to mount the 12V power supply on the wall. This bracket should work for any object with an OD of 98mm x 42mm. When making this on the Select Mini, you need to stand it up so the screw holes are flat...

I've got an affordable power inverter, but I needed to find a way to securely fasten it, so I made this mounting bracket on my own. As you can see from the pictures attached, this solution provides an exact fit and keeps everything in place with no...

This design is to replace the top cover of the Meanwell LRS-350 power supply so you can fit a Noctua A4x20 or A4x10 fan inside that sits vertically. I designed this because I used the Noctua A6x25 mounted facing down like the original design and...

I'm redesigning the Flying Bear P902's electrical system by adding brackets to safeguard its power supply alongside a dedicated power socket. As I refashioned this device, I decided to reorganize its electronic components with a focus on Blender...

## This is a quick bracket I designed in Fusion360 to mount an Anker USB Power Brick underneath a table. The screw mount holes have a 5mm diameter with a chamfer to 6mm so my 6.2mm diameter screw heads will sit flat. I've included the Fusion360...

Steering bracket made for Minn Kota. Tested on Minn Kota 36lb and it works perfect. ...Print it as follows: PETG 230/ 75 temp 100% Infill Supports not required, but you can put them if you want.

This is a custom enclosure designed to shield the Meanwell LRS-350 power supply from electrical shocks. Two openings allow for easy connection of power and on/off switch cables. Cable outlets are further protected by a rubber seal, guaranteeing a...

I've employed 2 existing models to design my Bench Power Supply: 1 - https://www.thingiverse.com/thing:2467237 2 - http://www.thingiverse.com/thing:2897335 Components utilized: - Control DC 6-55V to 0-50V 5A Step Down Stabilized Power Supply -...

This is a revised version of my MeanWell NES-350-12 power supply cover, featuring feet for improved ventilation clearance when mounted on a flat surface. I redesigned the original cover after building an enclosure for my printer, but aside from the...

It is custom designed for ATX power supply

Designed in tinkercad to mount a walmart brand power strip to the wall with screws. holes are for 8mm head screws. I measured my power strip to be 50mm wide by 34mm tall. HOLD POWER STRIP WHILE UNPLUGGING THINGS. ...

A sleek holder designed to secure the power cord neatly in position, thereby releasing the power supply connectors from stressful pulling forces.

Hello all! ...I'm showing you how to remove the power supply from my laptop - and it's really easy! ...The power supply measures 135x64x33 millimeters in size.

This system caters to the standard advanced 30-amp power source upgrade.

Power supply used: https://www.ebay.co.uk/itm/384284198672

I followed a Youtube video for steering damper installation by drilling a hole and using the middle stem bolt for mounting the steering damper. However, this one had a flaw as there was too much tension on the middle bolt that was always leading to...

I followed a Youtube video for steering damper installation by drilling a hole and using the middle stem bolt for mounting the steering damper. However, this one had a flaw as there was too much tension on the middle bolt that was always leading to...