30x30 to 20x20 stack adapter 3d models

This is my compact rendition of the original design found at thingiverse.com, specifically thing:2322516, with a significant weight reduction from 1.9 grams to just 1 gram. ... It resides atop a 45-degree tilted stack featuring a 20x20 grid layout.

The Foxeer Arrow Micro Pro Case is specifically designed for a 20x20 stack mount, accommodating angles between 0 degrees and 50 degrees.

Needed some more space for a 30x30 vtx in my new TBS Source One V3 With this part I was able to mount another 30x30 stack in the back/rear section of the TBS Source One v3. I printed the part in TPU, the holes for the post are slightly smaller so...

Q Frame started as a remix, however I wanted to be able to mount my old 20x20 stacks and keep the whoop style fc support. I´ve designed the frame for 0.2 layer resolution and layer multipliers in mind to get the ideal layer spacing/count without any...

Q Frame v1 A toothpick style frame that supports tbs crossfire and frsky xm+/xm receivers - fully accessible from the bottom tray. Q Frame began as a remix, but I wanted to keep whoop style fc support while mounting my old 20x20 stacks. The frame was...

Recommended Material: High-Quality PLA or ABS Plastic. ...Recommended Size: A Standard 20x20 Millimeter Stack for FrSky's Receiver, the R-XR. ...This TPU (Thermoplastic Polyurethane) Suggestion is a Great Option.

Install an AKK X2 Ultimate onto a 30x30 setup, secured firmly with zip ties at the base to ensure maximum airflow.

Thin adapter plate for tinyhawk freestyle quads, additional M2 screws needed.

... and not redo the whole base. There are two versions one where you drop your miniature in, and another which is a sleeve. Designed "support free" for SLA printing, and can be glued to your current bases. Base Converter & Sleeve for 25x25 to 30x30

Gps mount for the BN880 module. ... Works great on the side of the flight controller mounted on the long m3 screws.

This is a frame/bracket for the IKEA Lots 30x30 mirror, engineered to fit snugly into the original bed hole dimensions of the Tevo Tornado. Perfect if you've accidentally messed up your print bed and need a replacement. ...This design shrinks the...

This is an adapter to hold your SharkByte TX5S.1 video transmitter in a 30 x 30 stack. You need to clip off the corner tabs. I've included the Fusion 360 file for easy remixing. I've added another version to secure the SharkByte Vtx onto a custom...

Remix of the TBS Pod Racer Made the motor mounts for standard size motors, Top and bottom plates were designed to be milled from aluminum but carbon fiber may do as well. Pod has stand offs up under inside to mount the sharkbyte single board vtx,...

I'm operating a Martian 215 rear stock 20x20 paired with an R-XSR holder, utilizing a misplaced beeper configuration.

Quad FPV stack adapter plate to fit a 20mm x 20mm board to a 30.5mm x 30.5mm stack. The small diameter stand-offs are needed to miss components crammed onto the Caddx board but even then they may still need a little sanding to get clearance. You...

Quad FPV Stack Adapter Plate Originally designed to accommodate the Caddx Turtle V2 with HD DVR on board, as the supplied solution was deemed inadequate and unsuitable for its intended purpose. This quad FPV stack adapter plate enables a seamless...

... measuring 30x30mm in size. The following steps are essential for implementing this solution: Instructions: You can readily customize the provided Inventor version to suit your needs by scaling it up or increasing its dimensions as desired.

I lost the little plate that secures my antennas so these holes provide a place to glue in some extra filament and trim to 1-2 mm. Trim it just enough so it holds the antenna to the connector when you screw the vtx down to the platform. If you look...

Movement tray for use with new base size for old world, you can drop your 25mm square based figures into the movement tray, the tray is sized as if it is 10 miniatures base to base for 30mm square base. ...20 off  5mmx1mm magnets for holding the...

Here is a rewritten version of the text with all foreign characters removed and written in American English: This is an adapter for a 40x40 fan to use on the V1.1 XCarriage, which also serves as a cooling fan at the same time. It definitely needs...

UPDATE: Added a version with a base plate thickness of 1.5mm as opposed to the 2mm of the original. Quad FPV Stack Adapter Plate Originally designed for the Caddx Turtle V2 with HD DVR on the board as the supplied solution was, in my opinion, crap...

http://www.thingiverse.com/apps/customizer/run?thing_id=436118 Instructions Using the following settings: Corner Radius set to zero Width set at thirty units Hole radius at three and a half units Thickness set at six units Sides length set to forty...

I encountered an issue where the VTX wasn't connecting, so I created a solution to resolve that challenge

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

... Update: I've also added the Unify Pro32 Nano version, which features a button directly on the PCB. Compared to the original Nano design, this new model boasts an enlarged cut-out on the bottom due to the increased size requirements of the Pro32.

I made an adapter board to hold the Shark Byte board on the 30mm flight stack. ... The idea is to treat the adapter as actually 'nuts' that screw down on top of the flight controller.

this is a stack mount for the smr 450 to 20x20 stck

This connector makes it easy to stack boxes according to the widely recognized Euro container standard, as outlined on Wikipedia at https://en.wikipedia.org/wiki/Euro_container.

This adapter allows one to attach a second Lunt 40mm etalon to a Lunt 40mm dedicated solar telescope in order to produce a double stack configuration. It needs to be lined with the soft half of velcro tape in order to fit properly. M6x1 nylon bolts...