30mm fan mount 3d models

This is a 30mm fan mount for the front of the original Playstation. If you have something like MODE for Playstation and a hard drive in the console, it tends to get on the extremely warm side. I designed this mount to hold a 30mm fan. The fan is held...

18MM probe 30mm fan mounted.

A high-performance cooling system is equipped with a 30mm fan mount that accommodates wiring organizers, enhancing airflow and streamlining cable management.

The 30mm fan mount for Prusa i3 is designed to fit Wade's extruder, providing better cooling and improved print quality. This accessory ensures optimal performance of your printer by maintaining a consistent temperature during the printing process.

So I opted to use a 30mm fan mounted atop my printer. I made two versions. Nema14A is the one I use because I found that my assembly had a perfect fit tolerance so that I could simply slip the mount down onto the motor and it fit very snugly. Nema14B...

I made this fan mount for my Zion 8 printer. ...It fits a 30mm fan.

30mm axial fan 18mm ABL mount. Still need to redo the mounting holes. ...Should work for both standard and volcano setups.

I crafted this design specifically to accommodate a 30mm fan, and it was initially intended for use with the Castle Creations Mamba Monster 2 speed controller, which requires a simple zip-tie mounting solution. ...However, its versatility means it could...

I remixed the TEVO Tarantula 30mm Fan BLTouch designed by Keromida to make it compatible with my Monoprice Mini Delta. The "bottom mount" version attaches the mount to the bottom of the BLTouch, rather than the top as shown on my own machine. I'm...

Mount a high-performance 30-millimeter fan to maximize airflow and enhance cooling capabilities.

I ended up having a lot of 30mm fans rather than the standard 25, so I decided to use them instead. This will definitely work for the cheaper fans from eBay that often come with hot ends. ... Print Settings Printer: Fabrikator...

30 mm fan

30MM FAN MOUNT FOR INF1NITY IF14-II

Dual 30mm fan mount for a Raspberry Pi. Works on Raspberry Pi 3 & 4. ...

Simple 30mm Fan Mount for RC. ...Mount is inteded to be stuck down with double sided tape in the chassis.

This is an adjustable 30mm fan mount featuring a specially designed relief zone tailored to perfectly accommodate the East3D Gecko mounting configuration.

This is a prusa mendal (we call it the medusa) carriage with a 30mm fan mount. the end of the fan duct is a bit too close to the extruder in this version. It may melt. ... remix from https://github.com/josefprusa/PrusaMendel

This is a Prusa Mendel carriage with a 30mm fan mount.\nThe end of the fan duct comes alarmingly close to the extruder in this version, risking a meltdown.\nRemixed from https://github.com/josefprusa/PrusaMendel\nPrint Settings\nPrinter Brand:...

This is a custom fan mount designed specifically for an all-metal hotend with a 20mm diameter.\nthere are many available mounts for standard 30mm hotends, but I needed one that could accommodate my unique 20mm setup, so I took matters into my own...

I struggled to design a sturdy fan mount for my E3D V6 clone that stayed securely attached to the heat barrel, so I decided to create two adapters that attach directly to the stock 30mm fan mounts, specifically designed for 60mm fans. The PLA fan...

I designed this adapter that lets me mount a 4020 blower to a 30mm fan mount. It aligns to the top and it fits under my effector but it does hang out the back pretty far so be careful with larger prints. When I do my bed leveling routine the back of...

I created this adapter, which enables me to mount a 4020 blower to a 30mm fan mount. It aligns perfectly at the top and fits snugly under my effector but does protrude quite far in the back, so be cautious with larger prints. During my bed leveling...

This 30MM cooling fan mount is designed specifically for my Kossel 3D printer. My Kossel 3D printer features a robust frame constructed from high-quality 2020 extruded aluminum, with the two horizontal pieces on the bottom spaced exactly 30MM apart...

This is a simple low profile fan mount that works with most XV01 compatible RC bodies. ...It's designed to hold a 30mm fan in front of the motor.

A quick fan mount to attach a 30mm fan to the receiver cover on the latrax rally. 1st version is 45 degrees and the second is 30 degrees. 45* is tested and fits, but 30* may be a bit better for clearance. ... **Added a version 3 which is 30* with...

... mount the fan. i used a trinity 30mm x 30mm aluminum fan but the design should work with others and should work with m3 screws as well. ...as for the print, i used PETG as it handles the heat better than PLA but i have not tried using PLA either.

This is not a remix per se, but a simple extension for the Sapphire Dragon Orbiter project: https://www.thingiverse.com/thing:4583331 As mentioned in the original thing's comments, there is no built-in mount for hotend's 30mm fan. ... Here comes a...

It was a snug fit for the 30mm Rocket aluminum fan and I needed to open up the fan mounting holes to line up with the fan, but this will probably vary depending on what fan you use. I used M3x5 brass injection inserts to fasten it to the chassis...

Yes, another E3D 30mm fan shroud comes along. This one is admittedly not a genuine E3D, but it was purchased by someone else who is apparently okay with that. I had already printed several and wasn't thrilled with the result, so I made a new version...

I fabricated the "GIRO.remix - TEVO Tarantula / 30mm Fan BLTouch Mount by Keromida" to precisely fit on a 30mm fan for confined spaces.\r\nI used this with a custom E3D x carriage on my Tevo, which necessitated the heatbreak fan to be positioned...