308 bore guide 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=41246 Using the following settings: - Gear thickness: set to 5 - Number of teeth: specified as 10 - Pressure angle: defined at 21 degrees - Build plate selection: defaults to number 0 - Circular...

The following options were used to customize this model: Number of teeth: 60 Gear thickness: 13 Rim width: 5 Hub thickness: 13 Twist: 0 degrees Backlash: 0.5 units Circles per turn: 0 Rim thickness: 13 Pressure angle: 21 degrees Involute facets: 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=41246 Instructions Using the following options: 11_circles = 0 00_build_plate = 0 09_hub_diameter = 10mm 03_pressure_angle = 21 degrees 02_circular_pitch = 250 04_clearance = 1 degree...

http://www.thingiverse.com/apps/customizer/run?thing_id=41246 Instructions Using the following options: 01_number_of_teeth = 10 07_rim_width = 10 11_circles = 0 09_hub_diameter = 10 10_bore_diameter = 8 05_gear_thickness = 5 02_circular_pitch = 250...

An alto recorder featuring standard English fingering is distinguished by its straight bore and larger holes, requiring bigger hands. This design yields a tone similar to a Western concert flute. Listen to sound samples at the provided link. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=41246 Instructions Using the following settings: Build plate set to 0 Involute facets set to 20 Rim thickness set to 20 Bore diameter set to 8 Hub diameter set to 10 Number of teeth set to 20...

The tab at the front of my ring is and afterthought as a lifting point to slide vise and possibly as a point to mod, in a new STL, with a screw hole in the future for adding tool holder, solder guide, wire guide, parts tray etc. ...I'm open to...

I made this to cut resized .308 Win brass after running through a .300 Savage FL Sizing die. 1. Clean ,308 Brass 2. Lube very well (I use lanolin-based lube) 3. Resize .308 win to .300 savage 4. Cut to near size with this jig and a mini-cutoff...

Left side Sun visor holder for a Peugeot 308 CC. ...The snap ring substitutes the press fitting of the original one.

.308 Winchester/7.62 mm X 51 mm labelled loading block is sized for rifle cases with a rim diameter of .473" (12 mm.)

This is a battery cover for the Sekonic L-308. ... There are two versions, one that is just the model and one with the needed supports, easily removed.

Peugeot 308 GTI RC wheel rim 1/10 52 mm diameter 26 mm width 6.5 mm offset 12 mm hexagon

A hip flask model bullet case for five .308 bullets. Sliding lid, Rattle free storage. ... Added a model of a printable bullit as well.

Replace ventilation button of a Peugeot 308 year 2007-2013 but may fit more models0.2 layer high25%infillPETG

***V1*** key blank for Peugeot GTI on 208 and 308 models. ...If needed, adjust the scale to Z for maximum rigidity.

http://www.thingiverse.com/apps/customizer/run?thing_id=41246 Using the following options: 05_gear_thickness is set to 5 01_number_of_teeth is set at 10 03_pressure_angle is fixed at 21 degrees 00_build_plate is chosen as 0 11_circles are removed...

... Bore diameter is a standard 8 units. Hub thickness is established at 15 units. Number of teeth is fixed at 12. Hub diameter is precisely measured at 20 units. Rim thickness is set to a consistent 15 units. Twist has been optimized for zero degrees.

Bore diameter is established at 2. Hub diameter is precisely measured at 20. Circular pitch is calculated as 250 units. Pressure angle is expertly adjusted to 21 degrees. Rim width is defined as 5 units. Build plate setting is set to default, which...

A straight bore soprano recorder is showcased here, featuring standard English fingering unlike recorders from the baroque era and onwards. It offers a sophisticated tone with considerable chromaticism but at the cost of intricate fingering. The...

A comparison of widely used 308 (7,62) rifle calibers adhering to SAAMI maximum specifications includes the 300 ACB, 7.62x39, 308 Win 7.62x51, 30-06, 300 H&H, 300 Win Mag, 300 Weatherby Mag and 30-378 Weatherby Mag.

Button to replace the original button to move the ventilation flow to the left or right and up or down for Peugeot 308 Replace ventilation button of a Peugeot 308 year 2007-2013 but may fit more models 0.2 layer high 25%infill PETG

If you want a universal box for both 308 and Creedmoor, please print the new 308 or blank lid. I liked the design of this box from zx82net, so I decided to make one for my 6.5 Creedmoor range ammo. None of the original files will work with mine...

... opportunity to print it. Update: I created an alternative Soy Sauce Cap V2 model with a 3mm bore diameter, further expanding the options for those seeking a customized fit. ...Like its predecessor, this revised design remains unprinted at present.

This object allow the removal of the airbag on a peugeot 308 steering wheel. I'm using it to install a peugeot 308 steering wheel on my Citroen Ami. I've found a used peugeot 308 COD 98 171 150 ZD on ebay for 70 euro.   There are also the pieces to...

Couldn't find any car charger for my new 308 P5, so i made one myself.Bear in mind, I am a total newbie into design 3d stuff, but i think it came out okay.

Lego Pirate Ship Model №308(official). Lego model was made according to the official instructions. Some details may be missing or color may not match. The instruction number is indicated in the title. ...742 parts included.

I desperately required a 308 Win. conversion kit, yet managed to snag a 270 Win. conversion kit at an unbeatable price. ...Consequently, I seized the opportunity and designed a customized case feeder adapter to fit my needs perfectly.

Peugeot 308 GTI 2017 Printable Body Car, with different wall thicknesses. ... All models are prepared to be printed on different scales, the model has several versions with different wall thicknesses to facilitate printing

It is a Slot.it compatible chassis for the Ferrari 308 GTB by Scalextric( C 2974 or similar)with adjustable ride hide in front.It accepts in line Slot.it motor pods.Recommended filament PETG

Button to replace the original button to move the ventilation flow to the left or right and up or down for Peugeot 308 year 2007-2013 but may fit more models 0.2 layer high 25%infill PETG