3.5 sata hard drive caddy 3d models

Stackable Hard Drive Holders for 3.5-Inch Drives Mount Two 3.5-Inch Hard Drives Side by Side Used to Stack Mount Two 3.5-Inch Hard Disk Drives Vertically in Line. ...Similar to: http://i.imgur.com/7xeMHgJ.jpg

A compact storage rack designed to cradle up to three 3.5-inch hard disk drives securely and neatly.

this enclosure will hold 6 3.5" Hard drives and 2 120mm fans. ... bottom is cutout to be stackable.

This uses a 3.5 Hard Drive to be mounted to the wall. ...One side completes in about a hour print time.Needed:(#6-32 UNC bottom of drive)(#6 screws to mount to wall.)

This is a compact 3.5-inch hard drive holder, designed to securely store up to three drives at once. ...It's ideal for use with the popular LACC project, which can be found on Thingiverse under reference number 3483130.

Cooling for a hard disk drive 3.5 using a fan: 80x80mm is an option, as well as 70x70mm, 60x60mm, 50x50mm, and 40x40mm. ...If no specific fan size is provided, please add the details in the comments section.

... rented by banks. Support is not needed. This object main web page is: http://www.ctheroux.com/3-5-inch-hard-drive-box/ This object was designed using Solid Edge Community Edition. ... You can request the source files on the page listed above.

... rented by banks. Support is not needed. This object main web page is: http://www.ctheroux.com/3-5-inch-hard-drive-box/ This object was designed using Solid Edge Community Edition. ... You can request the source files on the page listed above.

This is a hard case for 3.5 inches hard disk drives. Designed to be stored horizontally (I store them upside down). You will need some felt pads, the ones I used are 3.5mm thick, roughly 1/8". ...You can change that value in the file, though, it is...

This is a holder meant to be able to vertically stack 8x 3.5" hard drives. There are 4 versions available. -Rails with countersink holes -rails with flat holes -no rails with countersink holes -no rails with flat holes. Rails are meant...

This is a stabilizing base for the Dynex 3.5" USB 3.0 external hard drive enclosure, and I'm fairly certain I bought mine from Best Buy. However, they now sell an identical model with the brand name Insignia. I based my design on the base of my old...

... modding projects targeting the Lian Li PC A-51. ...It accommodates a 3.5" vertical mount hard drive cage ideal for small cases, enabling users to install longer GPUs. ...The design integrates perfectly with both the front panel and floor of your case.

The item is a thin rail designed to connect with a typical 3.5" hard drive for installation within a tower computer. For years, I owned an unused hard drive because I lacked the necessary rails. Visiting local stores proved unhelpful and online...

I needed some feet for a 3.5" WD Red hard drive and quickly designed some in Fusion360.No supports needed! ...Lay flat on the bottom side where the hole is (see last image).<br>The hole was designed with the following technique and prints great as is:...

A Straightforward Test for 3-1/2 Inch Hard Drives. Secure Horizontal Desktop Installation. ... Print Settings Details Printer Manufacturer Information Printer Model: Prusa i3, CoreXY Raft and Support Options Rafts Required: No Supports...

I crafted this custom vertical mount after exhausting all available hard drive slots on my PC. ...The foundation of the mount is engineered to accommodate M4 screws and nuts with precision.

Mounting brackets for three and a half inch hard drives in the pci area of a larger case is feasible even with a small mother board such as mini itx. These mounting brackets are intended for use with drives that spend most of their time idle, however...

... I used that product to attach it to my case. I also needed some 3.16 x 1/4 long screws (standard hard drive screws). ... I printed at 100% infill for strength but you could print much lower, just make sure the walls are strong around the screws.

... include 0.125 inches of clearance around the hard drive. I'm going to add foam or some other material inside to keep it from moving and creating noise. *UPDATE 8/12/19* I reduced the clearance to 0.063 inches (1/16 inch) all around the hard drive.

I required a stackable hard drive caddy that could handle my low-power ZFS storage setup, utilizing USB portable hard drives effectively. This solution works flawlessly, leaving just enough space for optimal air flow to prevent overheating issues...

I wanted something to keep my hard drives not and neat and on a 2020 extrusion bar that I had. Designed this so I could fit a bunch in a uniform and spaced as fashion. HDs just need small 6#-32 Flat Phillips Heads to attach. This is what I used:...

I required a reliable method to Install a 3.5" Hdd in my arcade cabinet. Couldn't discover one that felt robust or fit properly so I created one. STL and Solidworks file included.. ... Print Settings Printer Brand: MakerGear ...

Thanks to Foron3d's innovative design, I've tweaked the dimensions to make it compatible with a Dell Precision Mini Tower's caddy space.

DS380B has issue with lack of air circulation, so to fix this im working on a mod that will turn the bottom caddy in to a plug in play fan that will draw air in from the front and blow it upwards past all the hard drives, since the case is pretty...

DS380B has issue with lack of air circulation, so to fix this im working on a mod that will turn the bottom caddy in to a plug in play fan that will draw air in from the front and blow it upwards past all the hard drives, since the case is pretty...

I'd had enough of cluttering my cabinet with loose stuff, so I built a caddy to keep the hard drive organized. I recommend printing with high infill settings. I'm pretty sure I did 100% for solid walls. ...Initially, I printed at 20%, but the bracket...

<p>I designed this model to fit in a HP Z240 full tower chassis. ...This will probably only work in computers with tool-less drive installation that is similar to the HP design.

Here's an expansion box design that's perfect for adding three more hard drives internally within a computer case. It prints best using a 1-1.6mm shell thickness, and to ensure a good solid cage structure, I highly recommend using a 100% infill...

Remixed the Original FreeCAD File with Fusion 360 to recreate a substitute for the "VMDCF" Dell Part. ...It's made for 14 and 15 Gen Caddys, *Update* It is now tested and works fine.

I still need to drill screw holes for securing it to the 3.5" caddy and the 2.5" drive - I will revise this once I print out a test. I designed it based on measurements of a production part that serves the same purpose. This was for a Dell server,...