3 jaw chuck for lathe 3d models

Parametric Chip Guard for Vevor Lathe The Chip Guard is connected to the slide using the screw holes for the moving rest. Required printed parts: - ChipGuard.stl (1x) Optional printed parts: - HexKeyExtender.stl (1x) Required other...

I tried the magnets with both poles facing the same, and both poles opposite; didn't seem to make much difference in holding strength, although "both poles same" might have been a bit stronger.Bolt the modified indicator to the holder (use the stem...

I designed a dust collection shroud to complement my existing 4-inch hose coupler, which I found on Thingiverse (https://www.thingiverse.com/thing:4198017), for use on my lathe while turning pens. The wait is almost over before I can print it out.

Made a dust collection shroud to go along with my 4" hose coupler (https://www.thingiverse.com/thing:4198017) for use on my lathe while turning pens. Haven't printed it yet though. Outside diameter of the round section is 100.1mm so it should fit in...

I'm building a tiny vacuum chip collector for my mini-lathe, which I use to turn pens. The chips produced by pen turning make an absolute mess. ... This design uses four 1/2" x 1/8" rare-earth magnets, available at Lee Valley (item C): ...

Made a dust collection shroud to go along with my 4" hose coupler (https://www.thingiverse.com/thing:4198017) for use on my lathe while turning pens. Haven't printed it yet though. Outside diameter of the round section is 100.1mm so it should fit in...

... so I did a fast redraw in Fusion360 using his mesh as a reference point. ... I've kept the mounting holes at 5mm and added a bit of room for adjustment, though they might need enlarging slightly if your lathe has M6 holes on the front.

Replacement Gear for ERBA 300 lathe, 80 teeth Print Settings Printer: Own build Rafts: Doesn't MatterSupports: No Resolution: 0,25mmInfill: 80% Filament: Generic PETG PETG doesnt matter Category: 3D Printing

The mount is held to the lathe with two M3 screws, and the encoder is attached to the mount with three M3 flat-head screws from underneath. One side of the mount is open to allow passage of a GT2 belt. Print Settings Printer: ELEGO Mars 2 Pro Rafts: ...

I design a custom handwheel for my mini lathe Hobbymat MD65, identical to Proxxon SD300. My lathe has no lock nut on its Z axis, only a continuous lead screw with 1mm pitch. Cranking the support is a tedious task with the original handwheel. To make...

Just put an 8mm rod into the chuck for tailstock purposes. The one inside the larger holder is too tight, which means you'll need to do internal turning in a single setting and use a sliding bearing that's 12mm outside and 8mm inside. If you have a...

The purpose is to attach it to an electric screwdriver or electric drill to open the chuck of a drill press that doesn't have a reverse. Print Settings Printer Brand: Anet Printer: A6 Rafts: No Supports: No Resolution: 0.25mm Infill: 100 Filament:...

With this tool, you can create precise rounding by employing a cutting tool and a traditional lathe.

With the indicator positioned in this manner and secured to the cross-slide, you can efficiently set up a 4-jaw or accurately measure a taper since the indicator is mounted on the slide, allowing for precise control over both X and Z axes. ...I have...

This low-budget DIY support for a lathe employs cost-effective stepping motors with 400 steps per revolution, ball screws, and steel plates with good parallelism. It boasts an impressive resolution of under 1µm and can handle hard steel parts due to...

This simple clamp adapted a Proxxon 50/E micromot handheld tool into a toolpost grinder for a 10" lathe. This should work for any similar tool with a 34mm diameter body Pictures show grinder in use as a cutter, grinding a 4mm tap and 3mm copper and...

... as the original, its outer diameter is significantly reduced. For others who may be facing similar issues, I have made available the Fusion 360 file used for this design, allowing potential users to adapt or modify it according to their needs.

simple DRO for Clarke CL500M and CL430 lathes. Holder attaches to the bed with magnets and a digital caliper is used to act as DRO. I put a slot in at the back that accepts 10mm threaded rod. This was in case i needed to add a clamp at the other...

The CNC machine begins with this cleverly engineered collet holder, which attaches seamlessly to an 8-inch lazy Susan for effortless rotation. Work is already underway on a custom Collet wrench, but it's still in the development phase. ...Stay tuned...

A straightforward clamp transformed a Proxxon 50/E micromot handheld tool into a versatile toolpost grinder compatible with a 10" lathe. This adaptation should be easily replicable for any similar tool boasting a 34mm diameter body. ... This setup is...

To enhance the appearance of my projects on Taig lathe, I struggled with manual finesse; however, it was nearly impossible to achieve desired results. Thus, I modeled and printed an adapter for the cross-feed, utilizing a DC motor with gearbox from...

Standard gears can be found here: https://www.thingiverse.com/thing:2523313 The same notes that appear for making the standard gears also apply to these, except that these two gears have STLs in standard millimeters. These gears are module 0.8, so...

I was having a bit of trouble slicing the chip tray STL by the-real-aga, so I did a quick redraw in Fusion360 using his mesh as a template. I've left the mounting holes at 5mm and added a little room for adjustment, though they might need enlarging...

it is capable of open ,close ,rotate actions to hold and move the objects

This is Grabcad account you can also follow on Instagram,Facebook and Thangs.Want to make 2d cad drawings? ...contact @mechtech_connectStarting from 1USD and 60INR.https://linktr.ee/mechtechdrawings

Parts and Assembly

This project were very interesting and I learned a lot throughout all this time in making this project.

A simple gripper is powered by an air cylinder, providing efficient and easy operation.

An Independent Project