3 8 socket holder 3d models

Simple 3/8" socket holder

3/8" Socket Holder on 5.5" X 5.5" square

3/8" Socket Holder on 5.5" X 5.5" square

This is a 3/8 socket holder that you can configure in a number of different ways to fit your needs.

Socket holder for 3/8" sockets

This holder is designed to accommodate 3/8" sockets and can securely hold up to ten individual sockets at once, providing efficient organization in your workspace.

This is a holder for 3/8" sockets. I used it for a set of 3/8" drive hex key sockets that came in a flimsy and huge box. ...This takes up much less space in the tool drawer.

3/8 socket holder for deep and shallow sockets. ...I went with an offset socket layout instead of linear to save length so it could fit on the print bed

Made this holder to store my 6 Points Sockets from the Husky Socket set. ... Deep Sockets - 8MM - 19MM Normal Sockets - 6MM - 19MM

Holds 3/8 chrome deep sockets from 8mm to 24mm with labels on the top of the stems. Painting the numbers makes them look quite nice so I'd recommend it. ...It will fit inside most tool draws as it's very compact.

Holds 3/8 chrome shallow sockets from 8mm to 24mm with labels on the top of the stems. Painting the numbers makes them look quite nice so I'd recommend it. ...It will fit inside most tool draws as it's very compact.

Holds 3/8 chrome deep sockets from 8mm to 24mm with labels on the top of the stems. Painting the numbers makes them look quite nice so I'd recommend it. It will fit inside most tool draws as it's very compact. ...Print Settings Printer Brand: Creality...

Holds 3/8 chrome shallow sockets from 8mm to 24mm with labels on the top of the stems. Painting the numbers makes them look quite nice so I'd recommend it. It will fit inside most tool draws as it's very compact. ...Print Settings Printer Brand:...

simple socket holder designed for 3/8 sockets. ...Should work around most smaller sockets. .3mm at 10% infill works fine.

3/8 socket holder for standard deep sockets.

3/8 socket holder for standard size sockets.

... to hang and have the pipe wrenches organized. Measurement: 3/8 Inch. Recommendation: Depending on the brand of the key, it is recommended to give - 0.1 horizontal expansion in Cura, so that it fits perfectly. ... I am subject to recommendations -

Printing: 15% infil, no supports required. ...

The 3/8 inch can be always in the holder, the exchangable parts are the 1/4 inch sockets. Purposely for nozzle removal but useful for other task also. Design from blank maker coin. socket adapter mine is 15mm wide. ... TALL holder grips more on...

Made this 3/8 inch to 1/4 inch socket adapter holder. Use 3/8 inch impact drill size for rigidity and compact. The 3/8 inch can be always in the holder, the exchangable parts are the 1/4 inch sockets. Purposely for nozzle removal but useful for other...

This is a holder for the 3/8 Allen sockets sold at Harbor Freight. It has 6 slots for 4, 5, 6, 7, 8 and 10mm sockets and the option to add a 12x3mm magnet at the bottom for additional securement. ...I have found that I didn't need the magnet, as it's a...

Designed for use with the Jet 3/8" impact sockets, both deep and shallow. Fits very tight so printed at 104%. ...Uses about 500g of filament

Nice little socket holder. Holds well. ...Needs to scale to 128mm wide to work correctly.

It holds 3/8 short sockets from 7mm to 22mm without skipping a any it holds them with no wasted space. I have used it at work for 6+ months V4 is cut into two parts to fit my printer. ...I glued them on top of some metal I had around.

The counter part to my 1/2 Socket holder. ... Made these for my tool box because using the holders they came in were a nightmare. 3x6 3/8 socket holder!

I tweaked it slightly by adding two additional holders while preserving the same amount of base width. ... You can also tweak the design yourself over at Tinkercad: https://www.tinkercad.com/things/iSru7ZoO0kv Be sure to check out Chuck's tutorial...

I couldn't find any other socket organizers that has the exact number of deep socket holders I needed, so I made my own. Each organizer prints in around 1.5 hours. Metric is for sizes 12, 14, 15, 16, 17, and 18. SAE/Standard is for sizes 1/2,...

I adjusted this to fill the bed of the Divinci Jr. ...It makes 8 rails that hold 7 sockets each.

This is meant to hold 8 3/8" drive sockets. ...I wanted to organize in a smaller area the harbor freight set of 3/8 socket to allen key sockets.

A holder for Craftsman 3/8 drive SAE hex sockets. I took the diameter of the each socket, rounded it up and then added 1mm to try and accept as many other brands as possible. Credit to user OmniMaker for taking care of the heavylifting with his...