3 8 hose fitting 3d models

<p>I found these on line ages ago, so cant take credit for whom uploaded them for free to share!</p> <h3>Print instructions</h3><p>Category: Props</p>

Pneumatic fitting for port G1/4 & hose 4 mm.

Fitting for connecting 1/2 tube to 16 mm hose.

Pneumatic fitting for port G1/4 &amp; hose 4 mm.

Angle fitting for tube 8 mm. ...1/8 inch thread.Link to aliexpress:https://megabonus.com/y/qoJY7

Angle fitting for tube 8 mm. ...1/8 inch thread.Link to aliexpress:https://megabonus.com/y/qoJY7

After 12 years of seasonal use, the flexible plastic hoses on my 3-quart LiquiVac motor oil extraction device had become brittle and no longer stayed securely attached to their fittings. Although the LiquiVac remains available for purchase from...

Hose joints with hex fitting tapered Outside diameter 1.0 mm Inside diameter 0.6mm Warning: nut fitting support with a wall 0.1-0.2 mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0,...

Hose joints with hex fitting tapered Outside diameter 1.2 mm Inside diameter 0.8mm Warning: nut fitting support with a wall 0.1-0.2 mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0,...

Hose joints with hex fitting tapered Outside diameter 1.4 mm Inside diameter 1.0mm Warning: nut fitting support with a wall 0.1-0.2 mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0,...

Hose joints with hex fitting tapered Outside diameter 1.6 mm Inside diameter 1.2mm Warning: nut fitting support with a wall 0.1-0.2 mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0,...

The dimensions of the 3/8-inch elbows, as demonstrated in the provided example, are measured at a 90-degree angle.

The 3/4 inch drip hose needed a sturdy peg to keep it securely in position.

It has a recess to fit an O-ring with a maximum of 17mm of diameter by 2 mm thick. The ridges large and small diameters are, respectively 7mm and 5.5mm. The fluid passage has 3.5mm of diameter. ... It was printed with the threaded side up, using...

Dillon 550 spent primer cup with 1/2" hose barb Made a stronger connection to the hose fitting V2 has the connection to the press more offset and shorter

1/8" male pipe thread on both ends with 7/16" hex in the middle. ...1/4" ID through bore

1/8" male pipe thread on both ends with 7/16" hex in the middle. ...1/4" ID through bore

A three Way Hose Connector for the standard push fit connectors. ... Note: A rubber ring seal is required for the end recess on each arm.

When utilizing a dust boot, it maintains the hose aligned. ...Attaches securely to the upper portion of a Shapeoko 3 machine.

Liked the design by PeterBrit, but wanted to be able to print with no supports, and needed to make hole bigger to fit over the rest of the hose crimp and fittings.

... measuring at 3/4 inches in diameter is what the product refers to. ...This particular item is specifically designed for fixing and mending hoses with a 3/4-inch diameter, making it an essential piece of equipment for plumbers and DIY enthusiasts alike.

Modification of SVideo's airlock design; fits a 1.75" vacuum hose. Included a wingnut to tighten securely around the hose, otherwise it falls off. Use an M4 x 25mm bolt, nut, and washer. Make sure you use a strong glue and print the wingnut in a...

- 1/2'' male BSP (British Standard Pipe) parallel threaded fitting (about 12.7mm) - 8mm INNER diameter hose adapter - for 18mm wrench HoseAdapt127.stl can be printed without any supports because a support structure is already modeled into the .stl...

I had stepped on and broken many of the fittings on the ends of my hoses, and wanted a replacement that fit ANY 2 inch connection - not just a particular brand. Through trial and error I ended up with one fitting with a OD taper that fits into any...

This should fit a hose with a 1.25" OD and a 1.0625" (1 1/16") ID This allows you to use a hose like the one that comes with the Home Depot Bucket head for approximately $24+ the cost of a 5-gallon bucket. A longer hose is recommended vs the stock...

... the washer, a smaller hole, and a smaller nut for reduced pressure on threads. The new version still fits regular hose washers but requires some force to install. ...It's stronger now, but only hand tighten it snugly, avoiding excessive force.

It can then be attached to a standard friction fitting for larger diameter vacuum hose with an outside diameter of 40mm. ... \ The internal face in this adapter is 40.5mm at the mount, narrowing to 39.5mm internally Fusion360 file available on...

This adapter provides an M25 Male on one end and a Male Garden Hose Thread on the other, allowing the jug to be used for pouring into another container (say, an RV) and not just dispensing. ...Be sure to only use garden hoses marked for Potable water!

......The problem was that none of them fit, neither the 3/4 nor 1 inch hose barb style, so I decided to design and print my own replacements. Initially, I attempted to use PLA, but it cracked every time I tried to install it, forcing me to switch to ABS.