3 5mm 3d models

This clip will allow to have a gain of 3.5mm of Z Height lift, giving you the ability to relax your bed springs for a more accurate bed leveling experience. You could give a small tack of glue to secure in place if desired but it is not needed at...

This is a case designed specifically for Adafruit's Breadboard-Friendly 3.5mm Stereo Headphone Jack. Depending on the type of printer and filament used, the lid may not fit perfectly. In that situation, try using cases with slightly different...

I couldn't find a case that fits the famous O2 DAC perfectly when my ODAC's 3.5mm jack is installed. So, I created one from scratch. The pieces should nest snugly inside each other - no screws or glue needed to secure them. The ODAC D/A Converter can...

Micro Jack 3.5mm male connector model offers versatility through its L-shaped plug design, making it suitable for detailed collision analysis when designing cases or PCBs, and also perfect for creating visually engaging presentations. This model is...

Edited TriangleFabrications' Nerf Longshot Brass Breech Bolt (https://www.thingiverse.com/thing:4240462/comments) to take the 3.5mm thickness orings I had. (R-22 metric size, 28mm ID). More or less preserved the clearance values that he had (Added...

A small keyring holder for the USB-C to 3.5mm headphone adapter. Uses the cable as the actual ring and the two connector slot into the body. When you want to use the adapter, just unclip from your keys and pull the cable out of the print. Highly...

A small keyring holder for the USB-C to 3.5mm headphone adapter. Uses the cable as the actual ring and the two connector slot into the body. When you want to use the adapter, just unclip from your keys and pull the cable out of the print. ...

These may fit sizes smaller than 3mm but will be quite loose and 3.5mm is roughly the maximum size. As of April 2nd, 2020, plans are in place to create Cable Keepers for sizes ranging from 2mm to 8mm. If you need a special size, please send me a...

If you want a different size, I will upload a 5mm here, because I have a 5mm and a 3.5mm in there so a total of 8.5mm short stroke. I do have some feeding issues but I think that's just because I have an M4 competition adapter and my M4 magazines are...

This is a simple 2 in 1 out 3.5mm jack audio switcher designed to allow you to swap audio inputs without needing to disconnect and reconnect cables. For this you will need 3 3.5mm audio jacks, a 3-Pole Double Throw (3PDT) Switch, and some wiring and...

This is an enclosure for Adafruit Breadboard Friendly 3.5mm Stereo Headphone Jack. Depending on your printer and/or filament types, lid may not fit your enclosure. In that case, please try models with slightly different dimensions. ...If you can edit...

The other hole accommodates a 3.5mm jack like this one, inset so that the threads are long enough and the nut lies flat. This 3.5mm jack transmits data to the WS2801 LED strip. The lid fits snugly with tabs. Printed dimensions measure 26x86x86mm. I...

This is my solution to getting extension cable from the back of my pc to the front of my desk and still being out of the way. Here are the cables I used: UGREEN 3.5mm Stereo Audio Extension Cable =https://goo.gl/qaP1z1 UGREEN USB Extension Cable USB...

To achieve this, I used the following cables: * UGREEN 3.5mm Stereo Audio Extension Cable: This cable allows me to connect my headphones to the back of my PC and route them out to the front panel without any additional noise. * UGREEN USB Extension...

If you own a OnePlus 6T or a newer model and don't want to misplace your USB-C to 3.5mm cable, simply use this easy adapter and you'll never have to worry about losing it. It's incredibly simple to print, requiring no support, and fits perfectly in...

The character height is set to 3.5mm. This project is still in progress, and the creator will continue to add more characters as they are needed or requested by others. The design is heavily inspired by Geert Keteleer's manual character set found at...

This is a two-part enclosure for the female end of FosPower 3.5mm auxiliary cables, enabling users to utilize it as a surface-mountable jack extender with #6 screws securing the two holes intended for mounting. My use case involved utilizing this...

Rather than the bulky proprietary cable, two of these can be printed to give the headphone two 3.5mm outputs, one at each cup. This is the connection system that Hifiman uses, which means that, if wired correctly, you'll be able to buy any...

These Bowden clips are supplied in 26 shim thicknesses ranging from 1.0mm to 3.5mm, in .1mm increments. Use the thickest one that fits under each Bowden clamp at the print head and feeder. When you find a clip that fits properly, it should stop any...

While I designed this for to accommodate 3.5mm patch cables to be used on my eurorack modular synth, this could be used to organize any number of similar sized cables. Or...edit the file and make it hold whatever. The size of the stand is 200mm in...

While I designed this for to accommodate 3.5mm patch cables to be used on my eurorack modular synth, this could be used to organize any number of similar sized cables. Or...edit the file and make it hold whatever.</p> <p>The size of the stand is...

I made these to clip onto the 3.5mm cables in my synthesizer setup because I have a few devices that I like to use similarly-colored cables across multiple channels, such as the MPC One (4x2 CV channels) and the BSP Pro (up to 8 gate...

I added openings for a 3.5mm Audio Jack, as well as one for a rotary encoder. The front of the case has been shaved down .25mm as one of my GBS Control boards was very tight in it. I added an opening to mount the LCD for the GBS Control into it.I...

I hate having cables just hang off my desk. I also regularly plug my guitar into my audio interface. Rather than pack away the cord several times a day, I made a couple of these to attach to my shelf. Problem solved! My shelf is about 0.75" thick,...

Disclaimer: Designed from datasheet and visual reference from pictures. I don't have the actual part to double check measurements. So this design is based on guestimation mostly. ...Useful for rendering/visuals, but not 100% accurate I presume.

Easy to assemble and functional "T" jack splitter that makes it simple to connect two different jack wires. I used PLA for the print, but I believe ABS would work just as well without any issues. ... If you enjoyed this project, please consider...

Trying out Solidworks for the first time

Customized version of https://www.thingiverse.com/thing:3013962 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3013962