3 5 hard drive caddy 3d models

For the ultimate combination, the third bracket allows you to mount both a 3.5-inch HDD and a 2.5-inch SSD in a 5.25-inch bay, using offset holes for better SSD connector alignment. Although other options exist, this set aims to provide a more...

This was a past project for a class, featuring an intricate 2.5" SATA hard drive from a laptop. Though not flawless, it demanded over 70 hours of effort and is impressively detailed. The design is in SolidWorks 2014 format; alternative formats are...

Holder meant to stack 2.5" SAS drives vertically.

2.5" Hard Drive Sleeve by RebelTaz For my storage needs, I have found that small-ish [coparatively speaking] internal hard drives in the ~250gb range are the far more economical option. I pick these up for like $5 apiece and combined with the...

2.5" Hard Drive Sleeve by RebelTaz For my storage needs, I have found that small-ish [coparatively speaking] internal hard drives in the ~250gb range are the far more economical option. I pick these up for like $5 apiece and combined with the...

2.5" Hard Drive Sleeve by RebelTaz For my storage needs, I have found that small-ish [coparatively speaking] internal hard drives in the ~250gb range are the far more economical option. I pick these up for like $5 apiece and combined with the...

The drive fits in easily and stays in place even without the top part -which is purely decorative-. WARNING: The first layer of the model has a honeycomb pattern. ...First layer adhesion might be an issue so, make sure to level your bed before...

There seem to be loads of 3.5 to 2.5 inch drive adaptor plates around but none that maintain the position or location of the power and SATA connector. This one does. I've tested it on my HP G6 servers and it works great for putting 2.5 inch SFF...

Adapter tray designed to fit a 2.5" SSD or HDD into a standard 3.5" drive cage or caddy. Important note: holes are intentionally precision-cut tight, allowing you to easily tap them with standard screws if necessary. Successfully fits Lenovo, HP...

This simple case is for a 3.5in Hard Drive.The hole in the front is for a SATA connecor.There is enough room for all hight drives

Securely fasten a 2.5" Hard Drive or an SSD Hard Drive inside a 3.5" hard drive bay using a mounting bracket. ...To do this, begin by placing the hard drive onto the adaptor before inserting it into the larger bay.

Simple Mounting Solution for Various Hard Drive Sizes A straightforward approach is needed when mounting hard drives of different sizes, including 3.5 and 2.5 inch models. The specific screws required depend on the drive type: M3 screws are necessary...

... all sizes without any issues. Note that there are no mounting holes on the frame for securing the caddy into a PC, as it's designed specifically for hard drive docks. ... The OpenSCAD file is available, so feel free to add mounting holes if needed.

Bracket Allows Easy Installation of a 2.5" Hard Drive or an SSD into a 3.5" Hard Drive Bay Installation Mount the Hard Drive into the Adaptor First; Two Screws Placed at an Angle Across the Square Opening Should Be Sufficient If the Holes Don't Line...

My Lian Li 'PC V1000 Plus' caddy had custom bolts to attach the hard drives. All now missing in action! I created a more common 'rail type' that locks the drives in. Took about 4 hours to print full replacements with 2 spare on an ender 3. Quite...

Adapter for ICY Dock Hot Swap Hard Drive Bay from 3.5" to 2.5" 7mm height. This adapter will allow you to use a 2.5" 7mm height SSD or hard drive (laptop form factor) in a Icy Dock hot swap bay. This was designed with the ICY Dock in mind, but...

It accommodates both 2.5" and 3.5" hard drives. Part A inserts into Part B and clicks firmly into place. The unit can be easily disengaged by pressing the release handles. I believe this part requires printing with ABS or PETG due to PLA's tendency...

A DIY project - a custom caddy crafted to secure a 4TB portable hard drive, specifically designed for use with the Netgear Nighthawk router when it's wall-mounted.

mSATA SSD to 3.5 inch Hard Drive Bay Converter. ... Required components: - An mSATA to SATA adapter, such as this one: https://www.aliexpress.com/item/2017-Universal-mSATA-SSD-To-2-5-Inch-SATA-6-0-Gps-Adapter-Converter-Card-High/32613616694.html - 2...

To build your own Raspberry PI NAS tray, follow these easy steps: Step 1: Print the custom tray design Step 2: Cut away the latch support as shown in the image below Step 3: Install your hard drive by pulling out the side latches and fitting it...

I know there are many 2.5 inch to 3.5 hard drive adapters , but this one is specifically Playstation 2 , its made to be slim so it doesent mess wit the airflow by blocking the vent holes that are in the expansion bay . ... There are mounting holes for...

The enclosure is designed to hold up to four 2.5 inch hard disk drives (HDDs), which are secured by clips on the edge of the case, preventing them from slipping out. There are multiple configurations available for the 3.5 inch case, offering between...

The holes that align with the hard drive are 4.0 inches apart, the holes used to mount to the drive bay are 3.1 inches apart. The hole diameters should be close enough to use the fasteners you might already have on hand. ... Print Settings Printer...

... ______________________________________________________________________ Replica of the HDD locking system for Synology NAS drawer. This version is specifically for the 2.5 "hard drive adapter (https://www.thingiverse.com/thing:4831668).

... à l'adapteur pour disque dur de 2,5" (https://www.thingiverse.com/thing:4831668). Replica of the HDD locking system for Synology NAS drawer. This version is specifically for the 2.5 "hard drive adapter (https://www.thingiverse.com/thing:4831668).

Remix of "Hard Drive Stand for Four or Six 3.5" Drives". ...This Version is Instead 6x ~25mm, 6x ~20mm and Can Hold 6x SLIM 3.5" HDD's (Typically Seagate 500GB-1000GB)

This is a direct replacement hard drive caddy designed specifically for Dell Precision M4400 and Dell Latitude E6500 laptops. To enhance its durability, print out the part as shown in the picture and carefully clip away the marked pieces in red. ...By...

For the famous and nowaday super cheap second hand Supermicro CSE-815 1U server chassis, I designed a harddisk caddy (hard drive tray) for 3.5 SATA/SAS HDDs. I liked the idea of https://www.thingiverse.com/thing:2413043 , but built these on my own...

2.5 case holds up to 4x 2.5 HDDs (clips on the edge to secure HDDs in and not let them slip out) 3.5 case made on various slots (2-6 slots) to print depending on your needs. There are 2 different versions, one with hollow bottom for placing an...

I had to rebuild my Plex server, and since I didn't have any spare drive sleds on hand, I decided to fabricate my own custom solution.