3 4 to 1 2 pvc adapter 3d models

I need to drive a socket with a 1/2" drive, so this adapter is perfect for the job. I initially tried printing it in a fancy way by standing it on its end, but that didn't work out. The layer adhesion was easily overpowered by minor misalignment...

The way to use on:https://nerd-corner.com/3d-printed-bit-adapter-square-hexagon/orhttps://nerd-corner.com/de/3d-gedruckter-bit-adapter-vierkant-sechskant/

The way to use on:https://nerd-corner.com/3d-printed-bit-adapter-square-hexagon/orhttps://nerd-corner.com/de/3d-gedruckter-bit-adapter-vierkant-sechskant/

The way to use on:https://nerd-corner.com/3d-printed-bit-adapter-square-hexagon/orhttps://nerd-corner.com/de/3d-gedruckter-bit-adapter-vierkant-sechskant/

Options Used for Customization: Height of 15 6 Arms Arm End Diameter is set at 5.0 Wall thickness: 2.0 millimeters Collar Thickness: 2.0 millimeters Arm Thickness: 2.0 millimeters Arm Compression Ratio: 1.0 Tube Inner Diameter: 28 millimeters Spool...

https://www.thingiverse.com/apps/customizer/run?thing_id=1803799 Instructions Using the following options: nozzle = .4 tap_height = 35 bot_in_dia = 31.5 top_in_dia = 29.5 bot_out_dia = 48.5 top_out_dia = 50 is_flange = 1 flange_dia = 53 flange_height...

A custom coupling for Vivosun (and similar) pond pumps with a 1" (nominal) male NPT threaded outlet, to connect to a 2" (nominal) PVC rubber coupling with a hose clamp.One side is a 1" FPT, and the other side is a 2" PVC slip fitting. Note that since...

I carefully assembled two existing flanges, a process that required precision and attention to detail - although I haven't run a print test yet, I'm eager to see if this will indeed function as planned. ...For all I know, I may have inadvertently scaled...

Generic 1/4 to 3/8 brass adapter.Manually measured.Designed in Fusion360.

Generic 1/4 to 3/8 brass adapter.Manually measured.Designed in Fusion360.

[1/2" PVC to 1/2" EMT Bushing](https://www.thingiverse.com/thing:5189276) [3/4" PVC to 1/2" EMT Bushing](https://www.thingiverse.com/thing:5189262) [3/4" PVC to 3/4" EMT Bushing](https://www.thingiverse.com/thing:5189264) Have a suggestion for a...

2" long steel adapter for 1/4" hex drivers. ...Ball detent secures 3/8" socket with square mounting shank.

2" long steel adapter for 1/4" hex drivers. ...Ball detent secures 3/8" socket with square mounting shank.

Adapter from 1/4 inch screws to 3/8 inch screws commonly used in photography, especially in tripod heads.

Simple adapter that converts the common 3/8" male threads found on microphone mounts to a 1/4" female thread used by other devices such as phone holders. Not as easy to find adapters to 1/4" female threads compared to male threads. ... If you need a...

For running pixels parallel to 1/2" PVC.

This is an adapter to go from a 3/8-16 mic stand screw down to a 1/4-20 camera mount. ...   Very light duty item.

Female 3/8"-16 to Male 1/4"-20 adapter. Designed to convert desk microphone boom arm to use standard camera tripod attachments. Print on side to prevent shearing when threading on 1/4" side. ...Suggest 100% infill for strength.

Simple adapter that converts the common 3/8" male threads found on microphone mounts to a 1/4" female threads used by other devices such as phone holders. ...Not as easy to find adapters to 1/4" female threads compared to male threads.

A simple adapter for 3" focuser to 2". Print in PLA without support, strong enough to hold a large camera. ...A screw could be used to ensure tightening.

This is an adapter that makes a standard 1/4-20 male thread compatible with a 3/8-16 thread. I recently purchased a Rode VideoMic Micro equipped with a lyre suspension mount, but unfortunately, it wouldn't fit on my tripods. ...To resolve this issue, I...

Adapter to fit 3/8 threads camera/lenses on 1/4 tripods. Print in sla for best results. The fit is tight, but better then too loose. The slot is to help inserting/removing it with a screwdriver. ...100% infill obviously required for a part this small.

Used to attach 1/2" pvc to 10mm coro. ...Perfect for displaying yard decor made of corrugated plastic.

This is a 3/4 female 90 degree bend to a 1" flex hose barbed adapter. Printed using both PLA and ASA seems to work ok. Supports used inside the tube are pretty difficult to clean out of the barbed end, so try and use as few supports as possible. ...

This can be used to mount a 3/8" camera onto more common 1/4-20 UNC tripod threads with ease. Alternatively, it serves as a means to get high-quality 1/4-20 threads into models printed at lower resolutions or with the thread printed on its side. One...

I transformed a broom or paintroller thread into a 1/2 in. PVC pipe adapter. Using this conversion, I fabricated a 2-foot extension for my paint roller. ...It's essential to have 100% infill to prevent the threads from breaking.

A PVC coupling with dimensions of 3/4 NPT and a length of 1 1/2 inches is available for download. Be sure to show your appreciation by clicking the heart button after downloading. Thank you for your support in modeling! Happy modeling, too! ...:D

My new workbench arrived pre-drilled with 1" dog holes, instantly rendering all my 3/4" size clamps, dogs, and stops obsolete. No problem at all if you have a 3D printer and can design a simple adapter that fits snugly in the bench and has a 3/4"...

This mount enables you to attach a 3/8" camera securely onto the widely used 1/4-20 UNC tripod thread. ... Alternatively, it serves as an effective method to obtain a high-quality 1/4-20 thread in a model printed at lower resolution or with the thread...

All 4 inch dust control is not the same. ... This is an adaptor for 4" Powertec and 4" PVC. It will slip inside the PVC and over the Powertec part. There are two files - one is a little shorter than the other. ...