3 4 1 2 adapter 3d models

It has that thread, and when used with an adapter for aligning it and the tracking camera, a unique length of 1/4" UNC bolt is required, which can only be found in specialized stores in Finland. This adapter offers a solution by allowing the use of...

This adapter converts between the Quadrant Drive and standard 1/4-inch hex sockets for compatibility with various hand tools including ratcheting screwdrivers and drill chucks. Using these adapters allows you to leverage existing equipment with your...

Adapter plate to mount a DSLR or any camera with a 1/4" screw to a polish krokus 35 enlargerBOM:¼" 17mm screw with head diameter of up to 16mmM14x45mm hex screw~25g of PLAdoesn't need to be 45mm exactly25% cubic infil

This is a custom adapter I created to install a Ramps 1.4 electronics board in the spot where my old Anet v1.0 board used to sit, which unfortunately died on me. ...The design leverages the existing holes in the frame for a seamless integration.

Adapters for cheap selfie sticks to allow the mount of 1/4" UNC bolts or nuts. There are two models. First one with a wheel, so that you can screw the bolt/nut into your device. In the second model, the blot/nut is fixed. ... Quick video to help on...

There are both 1/2-inch and 3/4-inch versions as well as versions that include a hex thumb screw for easy tightening/loosening (which I highly recommend--who wants to carry around a huge flat-head screwdriver just for plugs?). Note: I highly...

After spending half an hour trying to remove a stuck wing nut from a very innacessible place, I decided to make a tool for it.This adapts to anything with a 1/4 inch square socket, and has flat sides for better torque application if neededOriginal...

http://www.thingiverse.com/apps/customizer/run?thing_id=50663 Instructions Using the following settings: Coupler Length is set to 25 Five-Rotate Value is set at 270 degrees Six-Rotate Value is set at 180 degrees Hollow Feature is turned off Y-Four...

... the four and three readings on the gauge. ...Onboard, personnel are tracking 397 P-512s, while Defense forces report a remarkable 625 Mobile Personnel sightings. Meanwhile, Mission Parameter 2665-1 indicates that we're currently positioned on Floor 2.

You can find this on Amazon at...

You will need 6 M3x10mm screws for the lid and 2 M3x20mm screws for the blower fan. Be careful removing supports in the fan area. The lower front section can split because of thin wall from the fan notch. While I thought about reinforcing this I...

This is modeled to work with a ridgid shop vac 1 3/4 inch hose to a 1 inch hose to handle more vacuum attachments. ... 100% infil use heat to form fit after printing.

Standard Microcontroller Device PSOP SMD Chip Measures 8-Pin Dimensions Spanning 1.27 Millimeters Pitch, 5.2 Millimeters Length and 4.4 Millimeters Width.

This 3-D printed stopwatch uses an Adafruit 1.2" LED 4-Digit display. More details and Arduino code on the attached word document. ... I created this video to show you how this stopwatch works: https://www.youtube.com/watch?v=LXoiSQb2JJM&t=4s

A rapid adaptation of a 1/4 inch to hot shoe adapter with a printed thread was undertaken, utilizing a readily available design as a starting point. This particular model required only a 1/4 inch nut for assembly, which I fortunately had on hand. I...

It's a handy adapter that lets you turn 1/4" hex bits in tight spots. You can either hand-turn it or fit it snugly into a 12mm socket or wrench. This design prints with precision on my trusty Tevo Tarantula, although the bit does come out slightly...

I picked up an electric screwdriver to make working on my 3D printers much easierhttps://www.amazon.com/HAMMERHEAD-Rechargeable-Screwdriver-Patented-Technology/dp/B00S8D0ICG Unfortunately, it didn't come with all the allen bits I needed and my...

This is my first upload, hope someone finds it useful :) I lost the handle for my 4mm bit set, couldn't find a 1/4" to 4mm driver bit adapter so I modelled one. Then decided to do a handle as well. Print both vertical, no support, raft or brim.

I modified Michelix's ingenious adapter design to fit my i3 Mega with a SKR 1.4 Turbo board. The installation was a snug challenge, and I might revisit the tolerances to achieve an even tighter fit. However, it works perfectly as is, providing a 2cm...

I designed a universal adapter that fits snugly into 1/4" hexagonal holes, accommodating M5 nuts for easy use in the metric system. This part boasts a total height of 6mm, where 3mm is reserved specifically for the M5 nut itself, while the remaining...

The standard 1/4" bit and compact 4mm bit are designed to tackle any task with ease. The 4mm bit, in particular, is a staple in many screwdriver kits available at most stores, making it an excellent addition to my toolkit. ...It performs flawlessly,...

I plan on mounting it using a magmount adapter with a 1/4-20 screw. The anemometer base has four screw holes, so I created an adapter to fit the mounting needs of my project. The hole for the 1/4-20 is designed to accommodate a 1/4-20 heatset...

...So this is the opposite, 1/2 NPT female to screw onto the shower head, then 3/4 NPT male to screw the garden hose onto it. If you're using this for cleaning dishes or actually taking a shower, I recommend limiting the hose length as much as you can.

Please let me know if I overlooked anything and you run into any problems using the 1, 2 or 3 model variants! The nut and bolts required are M3. The nut that I used are 2.2mm thick. The bolts have a hex head that is 3mm thick and 5.3mm in...

Ceramic Capacitor THT 4x0.5mm-pitch 3mm-diameter 2.25mm-width

Specs: 1/4" (6.35mm) Hex compatible Description: 1/4" (6.35mm) Hex to 1/4" Square adapter With this toolhead, you'll be able to use any 1/4" square bits that you probably have lying around. This is just a tool head. If you need a handle or other...

Inspired quick&dirty mount from original V2.4R1 for the waveshare 4.3" Touchscreen.Liked the old design, so I made one for the Touchscreen. You can use the screws included with the touchscreen.  Slip the Display_Cover over the Display and...

The TSDSON-8 is a versatile Surface Mount Device (SMD) Chip with an impressive eight pins, offering a pitch of 0.65 millimeters and precise dimensions of 3.4 millimeters in length, width, and height respectively, at a diminutive 1.1 millimeter in...

Adapter for a 4" smooth pipe to a 3/4" threaded pipe

... of Thingiverse Project Number 656884 Created with Customizer! ... Instructions Using the Following Options Display Type Set to One Board Version Set to 1.1 Lip Thickness Reduced to Zero Lid Added to Design Overhanging Material Relieved by Ten Units