3 1 8 inches to mm 3d models

Hex bit to square adapter. ...I use it with my Bosch IXO.

These LED holder, allow the light to go in the fiber optic's. ...There are 3 different sizes, for the LED's (1.8, 3 and 5 mm)

These LED holder, allow the light to go in the fiber optic's. ...There are 3 different sizes, for the LED's (1.8, 3 and 5 mm)

Pipe hangers for all NPS standard size pipes, sized for the OD of 1/8 to 3 inch pipes. The OD is the same as listed in the table link to the NPS table https://en.wikipedia.org/wiki/Nominal_Pipe_Size Need help building your own project? ...email me at...

This is adapter for 3/4" standard water pipe to 30 mm diameter pipe, that I use in my projects.

This adapter fits a 3/4" standard water pipe to a 30mm diameter one, which I utilize in my projects. For high-quality female threading, print at 0.1mm per layer. Compatible with three vacuum sources: hair dryer (print this adapter:...

Collect three vacuum lines - from 40 mm, 2 inches, 2 and 1/2 inches to 4 inches Main part test and print in ASA - (0.6mm. 255C. 115C. 60% in fill, 15 % Fan, CURA DRAFT- 0.2mm lh) Feel free to support my projects!

The marking on this set is in inches (hence : 3/4, 5/16...) Sizes : 1/4" - 5/16" - 3/8" - 7/16" - 1/2" - 9/16" - 5/8" - 11/16" - 3/4" Estimated Print time @ 70mm/s : single bit : from 1 to 5 mn small set (1/4" to 1/2") : 15 mn big set (9/16" to 3/4")...

Adapter from 1/4 inch screws to 3/8 inch screws commonly used in photography, especially in tripod heads.

Simple 1" ball end to microphone stand (3/8 inch with 16 TPI) adapter. I made this to attach my Ram X-Grip phone/tablet mount to a boom microphone stand. ...For added grip, you can add plastidip to the ball end.

Simple adapter that converts the common 3/8" male threads found on microphone mounts to a 1/4" female thread used by other devices such as phone holders. Not as easy to find adapters to 1/4" female threads compared to male threads. ... If you need a...

3/8" to 1/2" Socket Adapter

Mic2Cam Adapter (3/8" to 1/4")

A simple 1/2" to 3/8" reduction fitting I made to adapt an aquarium pump to a 3/8" ID tube.

3/8" to 1/4" Hose Clip. ... Print with ABS in high heat situations

3/8" to 1/2" Hose Clip. ... Print with ABS in high heat situations

1" to 3/8" Hose Clip. ... Print with ABS in high heat situations.

Adapter from photography standard tripod screws 1/4-20 to microphone 3/8-16 screws

1/4" to 3/8" Hose Clip. ... Print with ABS in high heat situations

3/8" to 1" Hose Clip. ... Print with ABS in high heat situations

1/2" to 3/8" Hose Clip. ... Print with ABS in high heat situations

... Print in ABS or I highly recommend PETG. Print Settings Printer Brand: Ultimaker Printer: Ultimaker Original Rafts: No Supports: No Resolution: .200 mm Infill: 10% Notes: Perimeter shells >= 3 Post-Printing Sand Sand the tabs on 3/8" side to fit.

this one is for Sam, he has a 42 mm OD hose port on his saw and a 1 7/8 OD hose he'd like to connect to his saw.

The same as https://www.thingiverse.com/thing:2744354 but from 3/8 (medium size) to 1/2 (big one)

This inserts into a 3/8" inset to reduce it to 1/4" for use with standard 1/4" potentiometers. ...This was made to aid in re-using old General Radio knobs which have lost their metal reducers.

3/8 interior hole 1/2 outer diameter How I Designed This Designed on 123D Design

I needed a 1/4" to 3/8" adapter for an easy job, so 2 minutes in Tinkercad and 40 minute print and Bam. ... Not meant to replace a metal one but gets the job done for loose stuff and my 3/8" battery wratchet.

1/2" mpt to 3/8" barb. needed one for ecm so I didn't need to buy a brass one, so I made one. ...unfortunately v2.0 comes with one, right after I put in the work to make one, but here ya go anyways

Simple adapter from 3/8" to 1/4" tripod threads. I designed this to test the accuracy of my printer and strength of the printed part. Works great on Prusa i3 MK3S with PETG -- I might just use it! Please test the strength of the part and make your...

Most of them are 1/4" drive, but the last three are 3/8" and I wanted to keep them all on the same chain. Thus, this bridge link. This will probably require some supports until I can get the joint designed right. ...It's not like I can just cut two...