2x4 shelf brackets

Icarus - QIDI X-Max Carriage for Sherpa Mini R1 & Dragon / Mosquito / Zodiac x Phaetus & Dragonfly BMS
prusaprinters

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.Fasten the ribbon cable with...

DemonDeltaMicro - Simplest reprap delta frame to date.
cults3d

Fix them to the brackets with m3x10 bolts, make sure the heads go down into the recesses and are not high enough to touch the bed, or its insuation, otherwise heat conducts down to the brackets which being PETG will soften when at ABS temperatures. I...

Icarus - QIDI X-Plus / I-Mate (S) Carriage for Sherpa Mini R1 & Dragon / Mosquito / Zodiac x Phaetus & Dragonfly BMS
prusaprinters

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.Fasten the ribbon cable with...

Icarus 2 - QIDI X-Max / X-Plus / I-Mate / X-Maker Carriage (Orbiter, Sherpa Mini, LGX Lite)
prusaprinters

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.Fasten the ribbon cable with...

Icarus - QIDI X-Max Carriage for Orbiter 2.0 & Dragon / Mosquito / Zodiac x Phaetus & Dragonfly BMS
prusaprinters

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.Fasten the ribbon cable with...

Solder Fume Extractor for Parkside x20 battery and 12v dc adapter
prusaprinters

Power cut-off switch has been added.-Control panel redesigned to add a led switch and battery status monitor.-Added a led light bracket. .3mf files now have the proper print profile, such as ideal part position, layer height, fill and manual...

S22 3PO: The 3D Printed Option: KingSong S22 Suspension Slider FIX: Bearing Rollers
prusaprinters

However my analysis and testing shows a carefully designed 3D printed solution is actually better:All force is are supported within 2cm by steel bolts through to the aluminum bracket.Force is held on both sides of the bearings, no just one.Any force...

Temperature Controlled LACK Enclosure With Motion Sensor LED Lights
prusaprinters

In “Object Mode“ (top-left drop-down) > Object > Set Origin > Geometry to Origin.Helpers_Table_Corner.STL1 x Corner screw predrill helper (3mm drill)1 x Corner leg end alignment helper1 x Corner leg holder alignment helperHelpers_Leg_Ends.STL1 x Leg...

(V1) For BIQU B1 - DIY Enclosure - Remix of Prusa's IKEA Lack Enclosure - with extra doors (opening on 3 sides)
prusaprinters

Those sheets are: Bottom-Corners.stl Door-Knob-(x3)-and-Cable-Clips-(x10).stl Top-Corners.stl Top-Extenders.stl Additional parts that are not ganged up on a sheet with others: BIQU-B1-ac-heater-wire-redirect-strain-relief-bracket.stl (The main reason...

Flux Engine (Stand-alone)
prusaprinters

This part is not designed by myself, but I did change it to meet accurate dimensional requirements.electronics bay print bottom on the plate with supports so the cavities for the nuts are nice and clean.Supports on build plate should be enoughfront...

S4 Avant Lighted Logo
prusaprinters

S4 Avant Lighted LogoThis was a design I created as a retirement gift one of my best friends (lovingly nick named The Douche, no seriously, lovingly).  He had recently purchased an S4 Avant so I found this to be a fitting tribute to the...

X5SA PRO Bondtech Direct Drive V6 with BLTouch Mount
prusaprinters

With the new job as a driving force I finally got this to a working prototype. I solved the gap with the smooth rods by making some Z-rod compensator brackets. They seem to do the job ok. Included is a video of the printer making a 20mm calibration...