2wd backslash 3d models

Custom Front Wing and Rear Wing for Traxxas 2WD ONLY vehicles Provides adjustable downforce for speedruns! This is a pair of front and rear wings that have been designed to give adjustable amounts of downforce while producing very little drag. The...

Custom Front Wing and Rear Wing for Traxxas 2WD ONLY vehicles Provides adjustable downforce for speedruns! </h3> This is a pair of front and rear wings that have been designed to give adjustable amounts of downforce while producing very little...

Several robotics club kits were purchased from Banggood for a line tracing workshop. The electronics didn't fit properly on the robot plate, which made assembly necessary and required hot glue and careful drilling through brittle acrylic. The...

I crafted those components using Nylon-Bridge and Nylon-910, ideal for withstanding intense impacts. For assembling the body, I recommend applying contact adhesive to achieve a flexible bond. ...Now it's time to get creative!

These are beadlock rims I designed for my Tamiya DT-03 (Neo Fighter, rear: 12 mm hex; front: bearings) stock tires. After completing them, I'm fairly certain they'll function as intended. For now, I'll consider them work in progress. Parts needed...

Replacement Lower Front A-Arms and Front Bulkhead for Your ECX Buggy. My Co-worker Experienced Issues with Ours Breaking on Impacts, So I Measured and Modeled a Printable One to Make Them Easier to Replace. I Recommend Printing Them on Their Side,...

Front A-Arms for Vintage Losi XXX Buggy.These are not an exact copy of the originals, I tried to keep the same dimensions and geometry as the originals but they are beefier for a better/stronger 3d printed part. I have printed them, and used them. If...

I'm currently shifting gears between my classic speedometer cable and a modern VSS pulse speedometer designed for TDI engines. This specific speed signal sensor (VSS 8 pulses) comes from the donor car's Sharan (1998) model, which I sourced locally.

Originally designed for installing a Wild Turbo Fan on a 2-wheel-drive Slash, this motor fan mount should fit any standard 30-millimeter fan without a problem. This product attaches to the gearbox by removing the top two screws from the exploded...

A Custom Mount Solution for Integrating a Raspberry Pi Camera Module v2.1 onto a 2-Wheel Drive Robot Chassis.

This is a simple yet robust bumper designed specifically for AE's renowned Short Course Truck, weighing in lighter than its stock counterpart and effectively soothing the nervous rear end - trust me, it does wonders for mine. ... To achieve optimal...

So I was just cruising my RC one day, when I thought "What could take this to the next level?" and I came up with something amazing! It gives that awesome 'Merican look while the flags wave in the breeze. I knew that I would eventually flip the car...

Update 5/12/2015: Spent some quality time bashing with my Traxxas Stampede, resulting in a front A-Arm mount breakage. Repaired it by re-printing the part in a new direction and fortunately didn't encounter any issues this time around. I'm convinced...

I've always been impressed by the fact that switching from a 48-pitch gear to a 32-pitch gear on Traxxas 2-wheel RC vehicles has been a challenge due to the lack of a suitable gear cover design, until now. I'm not taking all the credit for this...

3D printable RC Car kit. ... All differential Axle parts available here and all other parts available from https://www.cyberbuggy.co.uk

PLEASE PROVIDE FEEDBACK AND PICTURES OF DAMAGED PARTS! THANKS! OR STOP BY IN A MONTH IF YOU'RE STILL OPERATING LIKE ME! I UPDATED THIS DESIGN ON 7/20/2017 AFTER CONSIDERING USER FEEDBACK THAT THE SOCKET FOR THE BEARINGS AND THE HOLES FOR THE SCREWS...

Since I had this gear cover printed out, I ran into a problem: there was no plug to put on that hole. You would have to get a Traxxas gear cover plug for that, but I decided to design a plug for my 32 pitch gear cover instead - it's modified from...

UPDATE: Version 3 Is Ready For The Field! This version 3 features several crucial adjustments that significantly improve its performance. The chassis hole position has been adjusted by a precise 0.5mm to ensure optimal clearance and minimize...

Hello, I created a LCG cover. 0.3 layer Megacubic I3 Printed w/o support. the holes are for glueing. v 0.3 add 2 mm on the sides, cover are double checked now! the hole in the front part is matching with the accu mount screw, you can replace and...

These snow-and-sand-ready skis excel on icy surfaces when fully utilized, showcasing superior traction when equipped with rear paddle tires for extra grip. Despite not requiring paddle tires for optimal performance, these simply mount onto the RC car...

<h3>Front A-Arms for Vintage Losi XXX Buggy.</h3><p>These are not an exact copy of the originals, I tried to keep the same dimensions and geometry as the originals but they are beefier for a better/stronger 3d printed part. I have printed them, and...

Arduino UNO and battery holder 2x 3AAA. ...To screw "arduino holder", you need spacers.

This custom part safeguards the rear bumper and suspension a-arms from being severely scratched over time when bottoming out on jumps. The long ribs on the Low Center of Gravity chassis near the motor and below the rear axle have worn down...

<p>This is another wedge and strap for a 3S LiPo battery <a href="https://www.thingiverse.com/thing:3657141">like this one here</a>, but this one is for batteries that are too long for the tray, not too thick like the previous one I made. I thought I...

This is a 3D printed radio-controlled buggy "E-Basner". This is a fast model to build. You need 1.1 - 1.3 kg of filament to print all the details for this model. Printing time 130-140 hours. The archive contains a folder with individual parts, as...

This is another wedge and strap designed specifically for longer 3S LiPo batteries, like this one here: https://www.thingiverse.com/thing:3657141. I created it to accommodate batteries that are too long for the standard tray, not too thick like my...

Front A-Arms for Vintage Losi XXX Buggy. These are not an exact copy of the originals, I tried to keep the same dimensions and geometry as the originals but they are beefier for a better/stronger 3d printed part. I have printed them, and used...

The account has been transferred to YB Cosworth.

This lipo battery holder was designed to make it easy for me to add a substantial 2S 5500mah battery to my RC Traxxas Rustler. To put it to use, you will first need to remove the plastic piece at the rear of the Rustler that typically supports the...

Arduino UNO paired with a dual 3AAA battery holder requires spacers to secure the arduino holder in place.