25mm base magnet 3d models

It helps prevent glue failures on magnets that you attach to a base by adding more surface area for the magnet and glue. ... It is sized for 3x2mm magnets, but you could easily edit it in 3D builder, or simply use a slicer to add an appropriately sized...

I like to put magnets and washers on my bases to give them some weight and make my minis easier to transport. ...This base is made to fit a 3/8" washer and a 6mm magnet.

25mm square base, designed to have 1off 5x1mm magnet and also has enough room for 1off M6 steel washers which can be hot glued in place, it is a push fit so make sure your printing tolerance is tight. ... Usable to replace citadel and similair bases,...

There were qutite some requests for this base since I've bublished Goblin King, a remix from Goblins by DuncanShadow. Sorry I could not fulfill it quicker but now it fianlly is here! ... Goblin King https://www.thingiverse.com/thing:4228194 ...

This is a base i made to go with my movement tray https://www.thingiverse.com/thing:3268512 it takes a 10mm x 1mm magnet I have included the source OpenSCAD file if you want to change any of the dimensions. ... UPDATE I have flipped the model upside...

The base requires a 10mm x 1mm magnet, which fits snugly into its designated hole without any need for supports. ... If you'd like to adjust the dimensions of the base, I've included the OpenSCAD file in the design, allowing you to make custom changes...

25mm base, designed to hold a 5x1mm magnet and also has enough room for an m6 steel washer which can be hot glued in place. ... Usable to replace citadel bases, but gives a little weight to a miniature and magent connection for transport or movement...

Just a remix I wanted so I could magnetise bases!

By putting steel instead of magnets into the bases, I don't have to worry about aligning polarity if I want to attach another piece to it or attach them to some other magnet. What other pieces might I attach? The Gloomhaven Elite marker (or any...

If you appreciate my work and have a few dollars to spare each month, please consider joining!Update (7/8/20): The magnetic tool holders have proven too strong (and heavy) for this purpose, so I've ended up getting a steel plate and placing magnets...

Magnetic miniature base that fits 5x2mm magnets. To attach the magnet, just add a little ca glue to the pocket and push magnet in firmly. ...It should sit flush with the bottom of the base or a little bit recessed, make sure it doesn't stick out.

a remix from 2942198, added a base that fits a 25mm holder, like to fit in my DnD shakeable miniature box https://www.thingiverse.com/thing:5928971 there is also a place at the bottom of the base to insert a magnet and added some solid 'supports' to...

Customized version of https://www.thingiverse.com/thing:3268537 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3268537

Hey, I created this base for my Adeptus Mechanicus Rangers and Vanguard. ...The magnet I chose was a 5mm by 1mm earth magnet.

A straightforward remake of the popular Devon Jones 2x2 layout, seamlessly adaptable to any 3x2 Openforge configuration. ...I'm unsure if this exists elsewhere, but after an exhaustive search, my own rendition is now available for your use.

Version 2 of a set of 25mm, 30mm, 50mm diameter circular bases that I designed for printing in resin, with underside compartments for holding 5mm diameter round 2mm thick magnets. Very useful for my own 28mm miniatures. ...Files include supported (for...

... 2 part resin. ...Height of the base is 6mm. The magnet hole is located at the bottom of the base, where a magnet with a diameter of 5mm and a height of 2mm fits perfectly. ...After inserting and securing it with glue, you can easily fill it with resin.

I wanted the magnetic elite base add-on to be sandwiched around the magnet instead of only on one side, so I created a 1mm thinner version of the original elite base. This worked perfectly for me with 10x2mm round magnets. I did not create...

Penny washer style magnet holder to glue onto the underside of models on 25mm bases so that a 6mm magnet (1mm thick) can be easily glued in place to hold to model to magnetic surfaces.

Magnetic bases featuring a recessed socket designed to accommodate 3x6 mm circular magnets are available, with the top cap serving as a detachable component that can be customized to either a flat surface or a intricately modeled base, pending...

I wanted to be able to add magnets to GW bases that are centered and flush with the base rim without dealing with two appoxies. This is my solution that works with the 5mm x 1mm round magnets I use. There's a little bit of wiggle around the outside...

I wanted a simple way to add a 5mm by 1mm magnet to the base of my existing minis. This can be printed and glued to the existing base. A magnet can then be glued in. ... I haven't actually printed/tested this yet so when I have I'll provide any...

I wanted a simple way to add a 5mm by 1mm magnet to the base of my existing minis. This can be printed and glued to the existing base. A magnet can then be glued in. ... I haven't actually printed/tested this yet so when I have I'll provide any changes.

This is a 25mm base for any table top gaming or models

... down to better unhook them. ... If you have any needs don't hesitate . Parameter 0.2 without adhesion or support. https://www.youtube.com/user/pheonix595401/videos https://www.facebook.com/Infinity3D-279332426036783/ Edit: Added a D3x3mm magnet slot.

Updated Bases for Phantom and Spirit Proxies now available at: https://www.myminifactory.com/object/3d-print-phantom-and-spirit-117088?fbclid=IwAR0L-A9yySiSht_0eqZ17q5fCpdWgQ3ZotoGRCv-DVpNTElfAwsy7R6GTX8

This base measures 25mm in diameter, perfectly accommodating the metal model's oval base within it, creating a seamless look by hiding its edge without needing to cut off the metal base.\r\n\r\nTwo versions are available - one with a flat bottom and...

Basic 25mm base with a small lip and a spot underneath to secure up to a 4mm x 2mm magnet.

base markers 25mm