240sx extended studs 3d models

This is a simple way to keep my extended antenna in my rig when not using it. ...I suggest using PETG, so the parts can take the heat.</p> Category: Electronics

I had some issues with taller prints using my old spool holder so I made this extended one.I used the hex pegs to align and give strength then glued it all together with 3D Gloop

SG22 (Spacegat 22) extended handguard that I added an angled foregrip to. I designed one of these with a picatinny rail, but wanted something a little more solid. ...Print on either end with full supports with PLA+ preferred.

I crafted a custom Glock 17 extended magazine release that fits my hand like a glove. ...The results are astonishingly precise, and I'm confident you'll achieve a seamless fit with the provided step-by-file instructions.

this is an extended battery compartment cover i made it so a bigger battery fits and i can get the connector out so i can power my goggles it works with xt30 and xt60 connectors

Extended version of https://www.thingiverse.com/thing:2641636 All credit goes to her! Print instructionsCategory: Containers

This is an experimental part. ...It will not last. I only made it to test the extended arm https://www.thingiverse.com/thing:4731777 and top link https://www.thingiverse.com/thing:4731795

This is the top link to mach the extended lower arm for the thunder tiger ts4n 1/10 rc car. Might need a small spacer at the shosk mount. Uses the original bolts. ...

this is a model for bersa 380 thunder. ...I printed with petg, 15% infill without support and work for me. The Model works like a extended grip, reduce recoil and gain more stability.

I required a bit extra elevation for my stand, so I promptly extended the riser component. ...This modification proved successful, but I observed a slight vibration at its new height, prompting me to add supporting cross members.

Same as the original but its been cleaned (Remixed from: https://www.thingiverse.com/thing:4805174) and extended to make it more comfortable to hold, and prevents thumb slipping over the top.

Modified from the breathtaking Modular Castle designed by the talented sablebadger, this extended drawbridge is perfect for gamers who love to roll a lot of dice. ... The original design can be found at: http://www.thingiverse.com/thing:1657208

Featuring an extended shaft, this accessory is specifically designed to work in conjunction with the Chrosziel 204-01 follow focus. ...Compatible with a wide range of Chrosziel follow focus setups, it offers seamless integration for enhanced control.

This is a basic remix of flygonials gryphon magazine release. ... I found it was a little too short for my liking so i extended it by ~8mm. ... This makes it easier to release magazines.

Remixed this one from jdpurcell's design https://www.thingiverse.com/thing:3494592 I had to extend the nose portion because I had a pair of safety glasses that had extra padding and wouldn't fit in the original.

This is an extended battery bay designed specifically for the ASW 28 v2 model from HobbyKing, tailored for users who rely on a 3300mah Zippy Compact battery and require precise adjustment to achieve optimal Center of Gravity (C of G).

The extended faceplate accommodates a 400x400 bed entirely, adding an extra 100mm to its overall width. ...Each piece measures 250mm in width, with plans to manufacture them using the BLV as soon as it reaches full operation.

A quick remix of the Trion carry handle by Gameface. ...Extended the length a bit and redid the screw holes for flat screws. ...Designed to fit my blaster design, the SPIRIT.

The Stokke Tripp Trapp Extended Glider offers supplementary support for the iconic Tripp Trapp child chair. ...This innovative accessory seamlessly integrates with the original rail system, providing extra stability and comfort.

Little brackets that can be used to extend a splash shield on a Brent Wheel splash pan. ...I used some cheap plastic kitchen cutting pads that are easily bendable.

Good day, today we're featuring the Mini Extended Bubble Bong. Never attempt to ignite plastic, as the toxic fumes are extremely hazardous - instead, utilize a glass bowl or attachement. ...Please note that I strongly advise against underage smoking.

I replaced the threads in the I3 Extended Spool Holder with the threads from Wanhao i3 Plus Bearing Spool Holder for Original Nut, a modified version that uses the original nut.

I'm printing a 2011 Ford Ranger Extended Cab model using advanced technology. ...The design requires minimal support structures, except for the mirrors and wheel wells, where additional reinforcement is necessary to ensure stability.

A wire relief mount for my ender3 when I extended it to a 400x400 and added a heatpad.I used PETG and printed on its side to give the best strength .

The original FM9 handle is very short and hard to grab on to, this is a longer version that extends it away from the top rail for easier action.

I love Baerbro's cross mount design however I needed a long screw for the extended cup. ...So I remixed his stl to match the others, only requiring a normal screw.

I had some issues with taller prints using my old spool holder so I made this extended one.I used the hex pegs to align and give strength then glued it all together with 3D Gloop

... of parts. A cooler duct extension was added, extending about 10mm for better insulation and also thickening the walls to boost rigidity. Additionally, I increased the bite on the part cooler fan screws. ...An extended duct remix is forthcoming.

... a common Samsung-sized battery (55mm x 36mm). This case features a side clip holder to ensure secure attachment. To install the new battery, simply remove your camera's back panel, connect the extended battery, and securely fasten the case in place.

Here's an extended door designed specifically for a modded Nerf Rayven. This door accommodates a Zippy compact 2s 1000mAh battery with no issues. The dimensions of the extended portion measure 4 cm wide and 2 cm deep. Overall, the length of the door...