20mm ball mount 3d models

Forum Thread: https://www.rivianforums.com/forum/threads/mounting-a-cell-phone-has-anyone-done-it.4636/ Mk 2e updates the sizing of the ball from 17MM to 17.2MM to better account for tolerance differences in the various mounts. 1" Ball Mount also...

This adapter converts from that sliding mount to a ball joint type mount. Updated - Added OBJ with the screw adapter instead of the ball. The ball would break off after a month or two of use. The new screw adapter holds up much better to daily...

This is a direct replacement ball mount designed specifically for use with the Rugged Ridge Dash Multi-Mount system. ...It serves as the primary connection point between the clamp and the molded plastic housing located prominently on the dashboard.

Ball with adapter plate.

"yewdrum" splatter ball gun

Ball mount for phone mounts. Dia 0.668 Had a wireless charging phone mount, but nowhere good to put it. I purchased this clamp (https://www.amazon.com/dp/B099QQRDVT?psc=1&ref=ppx_yo2_dt_b_product_details) to clip to the shelf in my jeep, and...

This is a remix of dkcwenge's Ram Mount Extension to be a 17mm ball at both ends of the arm. The ball is attached to the arm with an M4 screw.Depending on your printer you may or may not need supports for the openings in the arm. ... You will almost...

This is a ball head clamp for the GoPro designed to be used seamlessly with the 1" Ball Mount by WheresWaldo: https://www.thingiverse.com/thing:646007. It incorporates standard GoPro fasteners and nuts, ensuring effortless assembly. ...After printing,...

Use a bolt and two sides to make a threaded mounting Ram Ball. Use a nut on the other side to make a double sided ball. I used super glue to connect the sides and fill the gap around the bolt. ...It will also ensure the bolt and nut stay secured.

Ball & Socket Camera Mount, 100% Lock Up with a simple design. Try this one before the others. It's a solid build with no breakage. Will hold the heaviest equipment. printed @ 0.1mm ht for ball @ 50% speed 0.2mm ht for male & female @50% speed...

I created this alternative to the plastic ball mount on the DIGOO PIR, replacing it with a more durable option since the original ones tend to snap after extended use.

This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.</p> Category: Automotive

This is a replacement ball mount for the COBB Accessport. Print two and cement together, no supports are needed. I recommend 5 or more perimeters and a rigid, heat-resistant filament. ...FreeCAD file is included.

I've remixed this: https://www.thingiverse.com/thing:2153251 to create a sturdy ball mount for my trusty old discount webcam, giving it a new lease on life.

... GoPro to a GPS suction cup mount, I designed a custom 3D print model without finding any similar designs online. ...The mount is compatible with 17mm ball mounts and incorporates an internal nut for attaching the camera, eliminating the need for glue.

Hi, I designed this thing to mount an Go Pro to the already existing Ball mount for my navigation divice on my motorcycle The version 3 is without the useless thing around the mount. I printed it standing up with support and a raft. ... Greetings from...

Triple Ball RAM Mount Printed in High-Quality PETG Material Using a Precise 0.2mm Layer Height. ...Strategically Engineered with a Durable 75% Triangular Infill Pattern for Maximum Strength and Stability.

... a single unit. Thread the nut onto the mount before permanently affixing it to the base with super glue. The objective of this project was to have the mount firmly lock onto the ball with less than 1/2 of a turn. This objective was achieved. ...

Raspberry Pi Camera Mount that Attaches to a Clip-On Mobile Device Stand from Amazon, Which Provided a 17.2mm Ball. Remixed the RPi_Camera_Enclosure_Back to Add a Ball Mount That Snaps into Place. In Addition to This Remixed Part, You'll Also Need to...

Mount for making ball bunjees into essentially hooks. I use multiple of these in the extended cab of my Ford Ranger to hold anything from backpacks to jackets. Can be used anywhere though, this is just how I utilize it. ... Depending on the size of ball...

This Ball and Socket mount lets me position the camera exactly where I need it, and it stays put without any issues. ... The holes on this mount are designed specifically for 3mm screws, but before inserting them, I like to run a tap through first to...

Ball mount for use on popular GPS 17mm ball attachments Works in PLA. Better in PLA+ . Models oriented for best printing strength. Threads are close and need to be 'exercised' a few times before becoming smooth. Two collar and mounting base options...

Ball and Socket Camera Mount, 100% Lock Up with a Simple Design. Try this one first, it's a solid build with no breakage in sight. It will hold even the heaviest equipment with ease. Printed at: 0.1mm height for the ball at 50% speed 0.2mm height...

A secure platform (dubbed "Ball Mount") - devised by cgongora69 and featured on Thingiverse under #186545 - ensures stability for a variety of clamps or vises, can be adapted to hold small cameras too. This 3-part setup minimizes the need for...

I created this bracket to hold my Logitech Brio webcam on a ball mount, but it could be used for any webcam that supports the standard tripod mounting bolts. The ball head mount I used was this one: https://www.amazon.com/gp/product/B01CQAQOSI/...

For my door ball adjustment angle.

This 1-inch ball mount is specifically designed for attaching M8 bolts, allowing you to easily add accessories to your motorcycle or scooter. ...To properly credit this design, kindly visit http://www.thingiverse.com/thing:2970023 and link back to it.

Ball mount for izeeker dashcam, suggest using PETG for summer time temperatures inside vehicle. Version 2 has been changed to fit a little better. Print laying down on its back for easiest supports. ... I printed it in PETG with 80% infill to withstand...

Ball mounted bracket for Pi Camera module. This way you can adjust the angle of view to fit your needs . ... Designed to work with (but should work with many others): https://www.thingiverse.com/thing:3374914 Print-in-place, no assembly required...

A future version for the basic board may/may not be made ! Print Settings:No supports should be requiredBoth have been printed successfully with a 0.28 layer height (0.2 may make the Hextraction logo at the front of the mount look nicer)Fewer loose...