2020 toyota tacoma gas cap holder 3d models

This thing is a pair of adapters to connect your brake power bleeder to the master cylinder of your Tacoma and some other Toyotas. These master cylinders have a press on rubber cap and the universal adapter that comes with the pressure bleeder is a...

On the 1996-2000 Toyota Tacoma, an access panel below the headlight must be removed to remove the headlight housing, as shown in the picture. The small metal rectangular panel is held in position with a sheet metal screw and a plastic retention...

This iPhone 5 dock fits a 2009 Toyota Tacoma, replacing the passenger airbag switch and utilizing the Apple Lightning connector. Designed for an iPhone 5 with a slim case (similar to Elago S5), there's also an iPhone 4/4S version available. After...

Mount for a Tekonsha Prodigy P3 trailer brake controller to fit in a first generation Toyota Tacoma (1996-2004). The fuse panel cover replaces the cover for the fuse panel under the dash with a print-in-place rotating latch. I designed the hoop with...

The iPhone 4/4S dock for a 2009 Toyota Tacoma mounts in place of the passenger airbag switch using an Apple 30-pin to USB cable. Suitable for iPhone 4 or 4s with case, the iPhone 5 version is available here: http://www.thingiverse.com/thing:40254. To...

Introducing the 2019 Model Toyota Tacoma with an intricately detailed exterior and simplistic interior. The car features four wheels strategically positioned at each corner. Textures are included, while a separate zip file is also available for your...

... the spot in front of the middle cup holder. When printed it does has some minor ghosting on the outside from the coin holders but that is a minor thing compared to the added capacity. ...There is also a spot to roll bills and keep them together too.

Hi All, This is an adapter that lets you attach a NATIKA WD-011 camera available on Amazon to the factory backup camera location on a Gen2 Toyota Tacoma 2005-2015. I have a 2008 model that didn't come with the factory backup camera, so I got a Pop &...

This thing is a mounting adapter to mount KC Cyclone V2 LED lights under the hood of 2nd gen Toyota Tacoma. Adapters should be placed on either side of the sloped section of sheet metal along the front edge of the hood. These adapters will aim the...

These Replacement Knobs Fit Perfectly on Your 2016 and Newer Tacoma's Sliding Radio Dials, Replacing Those Slippery Originals with Secure Grip.

I use this cup holder adapter for my Tacoma, which fits perfectly into its third generation square cup holder area. It's perfect for holding my AirPod Pro and Ridge wallet at the same time. I also store business cards and pens/pencils in it. Avoid...

I didn't like any of the existing dash mounts for my cell phone, they all looked big and bulky sitting on the dash or in a cup holder. I designed this to follow the lines of my 2013 Tacoma dash. It use the RAM mount ¼ ball system, along with my...

This design requires one "dg_can_holder_V2" (the larger part that actually holds the can), two "dg_can_holder_arm_v2" (the vertical arms that connect the can holder to the bed rail), and two "dg_can_bed_holder_knob" (a knob that goes over a 3/8-16...

This mimics the OEM shift boot retainer on the bottom of a Tacoma shift knob that clips onto the shift boot when tightened. Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super...

This mimics the OEM shift boot retainer on the bottom of a Tacoma shift knob that clips onto the shift boot when tightened. Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super...

This is the custom-designed plastic retaining bracket for the sleek slim body piece located underneath the headlight of the 1st generation Tacoma trucks.\r\n\r\nWhile not an exact replica, this bracket fits perfectly and securely holds that body...

This mimics the OEM shift boot retainer on the bottom of a Tacoma shift knob that clips onto the shift boot when tightened. Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super...

Double toggle switch plate perfectly fits the compartment to the immediate left of the driver's control panel. ...Suitable for use with the extra-high Toyota shift buttons.

One of the few negatives of first gen Tacomas are their door handles which are known to crack. Some of the non-OEM handles are made out of a materiel that does not hold up in freezing temperatures. After snapping a handle this winter I decide to...

This version is a precise replica of the Tacoma's dimensions, untouched and unaltered for any RC chassis. Many enthusiasts have been eagerly awaiting this release. Additionally, this model features no windows. Specs: Wheelbase: 313mm Width at bottom...

One of the few negatives of first gen Tacomas are their door handles which are known to crack. Some of the non-OEM handles are made out of a materiel that does not hold up in freezing temperatures. After snapping a handle this winter I decide to...

Mounting a colorful TRD emblem on the grill of a 2022 Tacoma is next to impossible using the retainer that came with the product. The badge is too large to fit comfortably inside of a “honeycomb” and would have to be mounted protruding outside of...

I created this based on the idea I found in the 4Runner and adapted it for use with my 2nd Gen Tacoma (2009). I built using PLA at a 0.2mm layer height, and it looks fantastic. I would recommend four solid top and bottom layers and two to three...

The Vehicle's Fuel Tank Needs to be Sealed Properly Using a Gas Cap for Safety and Efficiency Reasons.

People often need to remove a cap-like tool that's stuck on a broken gas cap for their 2005 Ford.

Price: $199.99 Date listed: May 22, 2023 Most recent update: Aug 18, 2020 Product code: 23456789abcdefg

The 3rd Generation Tacoma requires a secure fastening method to prevent damage from road vibrations. A square dash insert is an excellent choice, but it's essential to use a filament with high thermal stability to avoid melting inside the vehicle.

Remixed the design of Toyota Sienna Key Fob (XL30) by roflowhale at https://www.thingiverse.com/thing:1463458, making significant improvements to its functionality and aesthetic appeal. I'll be uploading pictures once it's printed out, showcasing...

When installing an "add a fuse" accessory to the fuse box underneath the steering column of a 3rd gen Tacoma, it becomes impossible to fit the stock fuse cover back on without modification. This fuse box cover is designed to provide added clearance...

Mine has the Toyota lock (or is it a McGard??) and I simply could not get the tip of the crank with the lock key into the drive. It turned out that I was missing a part that would guide the tip into the slot. I don't recall what was there before but...