2020 Filament Guide Block 3d models

Simple filament guide for beam aluminium printers. ...My filament was going everywhere without this in my Hictop Prusa i3 printer.

This is a versatile filament guide tube mount designed specifically for attaching to 2020 extrusion profile. The base, tube mount, and retainer work seamlessly together using an M3 bolt threaded directly into the plastic. The base securely attaches...

This filament guide is most useful when your spool is mounted to the side of your printer. If it's mounted to the rear, check out the remix by [soupkitchen](https://www.thingiverse.com/soupkitchen/designs): https://www.thingiverse.com/thing:4624339 ...

If the filament guide is too tight, users can try printing it in Slic3r Prusa Edition (Free), which produces dimensionally accurate prints according to my experience. On the other hand, if the filament guide is too loose, users can try printing it...

This revised version of the Sloppsta filament guide for the AM8 prints quickly and uses less filament. The installation process is straightforward, thanks to the strategically placed screw hole that avoids obstruction by the guide tube. ...The tube...

Filament Guide For 20x20mm v-slot aluminum. Requires t-nuts and bolts and 2x V-groove ball bearings. ... Very quick print.

Simple guide helps keep filament on track in DIY aluminum beam 3D printers. ...Without it, my filaments scattered all over the place, causing chaos with my Hictop Prusa i3 machine.

The user remixed FragrantAbyss' guide arm to seamlessly fit Filboyt's end clip for his filament guide. ...They carefully redesigned the piece to securely hold the filament in place, reducing stress at both points where it meets the extruder and making...

Unfortunately as I printed it from PLA, after only one spool, the filament carved its shape into the guiding ring, causing it to stutter and even cause retraction issues. I designed this simple insert that clips on the guiding ring and houses a...

It allows the direct drive (https://www.thingiverse.com/thing:3369418) to fully clear the top gantry while providing a vertical pull on the filament even if it is mounted off to the side on the table or even attached to the bottom of the printer...

Snap-on arm designed to hold a 6.9-7mm dia x 6 mm long nylon spacer/bushing at just about any angle to provide a very low-friction filament guide. Your choice of ~3cm or ~7cm offset. Fits 2020 Openbeam (not planning to add instances for other...

... input end that accommodates filament movement across the spool. ... Designed to guide your filament from a left-side spool holder down to the extruder, this add-on features holders that allow you to insert the filament while it's in the extruder.

This is a filament guide that snaps securely on to popular aluminum extrusions used by a variety of 3D printers. Parts for 2020, 2040 and 3030 extrusions have been included. I deliberately avoided adding notches to fit into the extrusion channels...

This is a straightforward rehash of Xlnzee's filament guide, adapted for use with a twist-in plastic groove design that eliminates the need for nuts or screws to secure the guide in position - purely due to my own inherent laziness.

Filament guide. ... Things included in the design: - Reduce the material required, whilst still being functional - Push fit so no other parts required Supports are required for the locating tabs.

Filament Guide For 20x20mm v-slot aluminum. Requires t-nuts and bolts and 2x V-groove ball bearings. Very quick print. ... If you like the design please consider a tip: https://www.paypal.com/paypalme/thisrudager

I upgraded my filament management system by relocating the loop's entrance, resolving issues with retraction. The modification was prompted by frequent filament slippage from the original setup. I opted for a 2020 connector, finding that its longer...

Snap-on arm designed to hold a 6.9-7mm dia x 6 mm long nylon spacer/bushing at just about any angle to provide a very low-friction filament guide. Your choice of ~3cm or ~7cm offset. Fits 2020 Openbeam (not planning to add instances for other...

this guide block fits over the PC4-M6 fittings I use and has 1.8mm wide 682X bearings and uses M2.5 hardware for bearing shafts to allow the filament to bend in any direction. The block slides over a PC4 fitting and has a screw and captured nut setup...

Couldn't find a filament guide that would suit my needs, so I decided to make my own in Sketchup. It features a 608 bearing that makes sure the filament runs smoothly to the extruder. Bearing fits snugly but I recommend adding a screw and nut just to...

The guide boasts an 8mm bore, making it effortless to thread and capable of feeding multiple filaments without getting stuck. This twist lock fitting simply requires insertion into the V-slot and a clockwise turn of 90 degrees, securing it firmly in...

this guide block fits over the PC4-M6 fittings I use and has 1.8mm wide 682X bearings and uses M2.5 hardware for bearing shafts to allow the filament to bend in any direction. The block slides over a PC4 fitting and has a screw and captured nut setup...

In addition to the bearing, you'll also require an M3 bolt and nut, both of which play critical roles in securing your filament guide in place. With these essential components, you're ready to take on any project that comes your way. Whether you're...

To improve print quality, I increased the size of the opening in the filament guide, making it less restrictive than the original design. ... Print Settings: Printer: Cookie Bot Rafts: No Supports: No Resolution: 0.2 mm Infill: 20-60% Notes: To...

I only revised the filament guide, that is the file you will find here. It requires minimal support for the arching holder. I made the holes in the middle to use less material and create a sleeker appearance. It stands at an impressive height (13 cm)...

I only remixed the filament guide, that is the only file you will find here. It only requires small support for the arching holder. I made the holes in the middle to use less material and to make it look cooler. It is so tall (13 cm) because my spool...

Since Printables can't import Thingiverse remix sources (yet):This is a remix of the following model(s): https://www.thingiverse.com/thing:2917932   Since my filament kept sliding out of the loop due to my high retraction, I decided to...

Basic attachment guides designed specifically for aluminum profiles.

I wasn't thrilled with the reliability of other filament guides for the Ender 3, so I created a sturdier one. It features a 5/16"-18 Thread Size, 2-1/4" Long bolt, as well as a 22mm OD, 7.8mm ID bearing. Remodeling this for your specific hardware...

Modified to suit 2020 extruder specifications for optimal performance on Ender 3 printers