2013 ford flex cup holder insert 3d models

Designed specifically for a 2013 Ford Fusion cup holder, it should fit most cup holders with ease. Holds: A 2013 Ford key fob, nail clippers, breath strips, chapstick, and has a large pocket for other miscellaneous items that you may need to carry...

... the center console. ...It may also fit other Ford models. Similar in design to the original cup holder provided with the vehicle, this insert stands a bit taller and wider to accommodate smaller cups and the slightly deeper driver's side cup holder.

Similar to the original cup holder provided with the vehicle, but tweaked to accommodate smaller cups and the slightly deeper driver's side cup holder, this insert stands out with its slightly taller and wider profile. Print Settings: * Printer:...

This is a cup holder insert made for the 2015 Mondeo/Fusion for smaller cups in the center console. Might fit other Fords. Much like the original supplied with the car but a little taller and wider to account for smaller cups and the slightly deeper...

The cup holders are an unacceptable 87.6mm (3.4inch) in diameter, which is far too large to properly support smaller than standard cans. My MtnDew Kickstart, IZZE juice, or other 8.4oz (248ml) or 12oz (355ml) cans desperately needed support, so I...

It slips into the cup holder and stops just above the illuminated ring if your vehicle is equipped with such. A light, fast, easy print. I recommend a TPU filament for shock absorbing if that's your thing. Also easily stores in glove box or other...

The cup holders on my car are ~87.6mm (3.4inch) in diameter, way too large to properly support smaller than standard cans. My MtnDew Kickstart, IZZE juice, or other 8.4oz (248ml) or 12oz (355ml) cans needed some serious backup, so I took matters into...

A replacement cup holder insert for a Ford Edge

I modeled and printed replacement cup holder inserts for my 2016 Ford Explorer. The model is 80mm which will fit the front cup holder. ...Down size by about 10% to 70mm for the rear cup holder.

I designed and fabricated new cup holder inserts for my 2016 Ford Explorer, matching its specifications. The original model measured 80mm in diameter, a perfect fit for the front cup holder. ...To accommodate the smaller rear cup holder, I scaled down...

This is a special insert designed to it into the 2019 Ford Edge console cup holders. Not sure who the idiot at Ford was that designed these oversized cup holders with lock jaw brackets. The fingers on the sides of the cupholders are so tight that I...

Basic Cup holder insert for a 2016 Ford Expedition to hold a pop/soda can.

A replacement cup holder insert was desperately needed for my son's trusty 1993 Ford Bronco. Fitting it wasn't attempted yet but dimensions match up nearly exactly already. (The left side is printed with precision, right one comes OEM from the...

Inserts are designed to fit standard-sized bottles, but can also accommodate smaller water bottles, providing a secure fit.

The problem was that the cup holder in the door isn't a full circle, so the vape constantly slides out of the cup holder. Keeping it in my hand while driving wasn't desirable either. ... This solution promises to make your vape quickly accessible while...

I lost the coin holder for my 2009 Ford Flex so i created this one as a coin, vape pen, bic pen, dollar bill holder. ... There is a cutout on the back that lines up with the mounting for the OEM coin holder to help keep it in place.

This is a base for a Ford car cup holder. It stops cans and cups going all the way to the bottom of the cup holder. Infill of 15% should be fine. ...The flat part goes at the top and the fins go at the bottom.

I made a Ford cup holder separation with a 19 mm hole. For example, you can use a button for an additional horn. You can sand the surface, but be careful not to destroy the tips. ...(like in the picture)

MY stock Ford cup holder was not practical. This new design works great! Hope this helps you out like its did me, Coffee is life my friend. ... 2 designs if i mount the Double cup i'll post pic for now i like the 2 cups mounted to the T joint.

I'm Adding Cup Holders to My Ford E350 Project. It Only Came with One, and That Wasn't Enough. So I Used My E150 Wooden Template to Create a New Holder for My E350. This Design Can Be Resized to Fit Most Van Center Consoles. ...To Make the Opposite...

It originally came with a single cup holder, which was insufficient. I utilized my E150 wooden unit as a model to create an additional one for my E350. This design can be easily scaled up or down to fit nearly any Van Center Console. ...To create the...

I built a custom cup holder insert to safeguard my 16.9 fl oz can of diet Mountain Dew against movement within the cup holder of my 2008 Ford Explorer.

Here's a perfect fit for your 1987-1993 Mustang: a custom cup holder (and change tray) that fits seamlessly into the ashtray space. The clever design slides down easily, leaving no gaps or obstructions. I put it to the test by driving with a full cup...

2015-2020 Ford F-250/F-350 Super Duty Cup Holder Insert Specifically Engineered for Nalgene Bottles. ...Reinforced with Additional Holes on Sides to Secure Ram Mount Ball Adapters Holding Smartphones in Place.

I've created a custom cup insert for my Ford Focus 2012 specifically designed to securely hold my camera rig.

This is an insert for the cup holder in the center console of a 1995 Ford Bronco. ... Print Settings: Printer: Zortrax M200 Rafts: Doesn't Matter Supports: Yes How I Designed This: I took precise measurements of the original part, then brought those...

This insert must be used with existing cup holder. Vertical portion of insert prevents insert from rotating in the cup holder. Insert printed as shown in image #3. I have printed on glass and PEI bed without use of skirt, brim or raft. ...Used .04...

This is a cup holder insert for a Purell 8oz hand sanitizer bottle. ... The insert keeps the bottle stationary while driving.

thing is cup holder insert you can adjust its size in your silcer to fit almost any cup holder has a mesh for air flow and looks it needs 0% infill Printer Ender3 V2

Crafting a versatile component like this can enable the creation of a secure and snug cup holder insert, accommodating any cup size with precision. ...Its potential uses extend far beyond its primary function, awaiting discovery in various innovative...