2 grommet 3d models

Customized version of https://www.thingiverse.com/thing:2820714 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2820714

Customized version of https://www.thingiverse.com/thing:2820714 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2820714

Customized version of https://www.thingiverse.com/thing:2820714 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2820714

Customized version of https://www.thingiverse.com/thing:2820714 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2820714

Customized version of https://www.thingiverse.com/thing:2820714 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2820714

Customized version of https://www.thingiverse.com/thing:2820714 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2820714

Customized version of https://www.thingiverse.com/thing:2820714 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2820714

A 60mm fan for better Raspberry Pi and Einsy ventilation can be installed. Helps to extract odors from the enclosure and remove them using an optional 50mm suction hose. See...

The grommet will fit into a 1/2 inch hole in the enclosure and the grommet cap will allow a cable up to about 3.5 mm in diameter. Print instructionsThese are the settings I used for my prints. Resolution: 0.20mm Quality Material: PETG Supports: None...

<p>I designed this to pass cables through the top of my desk. I printed it with a .6 nozzle at a .3 layer height. ...This should be a friction fit, if it is too loose I added a small amount of electrical tape to increase the diameter.</p>

Customized version of https://www.thingiverse.com/thing:1030514 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1030514

The project required drilling a precise 1/2-inch hole on one side of the panel and designing a grommet that would securely hold cables in place within the hole. To achieve this, I threaded my antenna wires through a pre-cut slot and inserted foam...

I needed a 1/2" hole on one side of the panel and wanted to make a grommet that I could slide cables into that would stay put inside the hole. I ran my antenna wires through the slot that is cut out and stuffed some foam inside with the wires to...

I needed a 1/2" hole on one side of the panel and wanted to make a grommet that I could slide cables into that would stay put inside the hole. I ran my antenna wires through the slot that is cut out and stuffed some foam inside with the wires to...

... the original size was slightly off. I've corrected the 1.75-inch version and also uploaded a 2-inch and 2.5-inch version. If anyone needs an additional size, please let me know. ...I've re-done my Solidworks file so I can quickly adjust the size.

I've corrected the 1.75in version and uploaded a 2in and 2.5in version too. If anyone needs an additional size, just let me know - I've re-done my Solidworks file so I can quickly change the size. Print Settings Printer Brand: LulzBot Printer: TAZ 6...

https://www.thingiverse.com/thing:4441076 presented a thumbscrew to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

These spacers and screws allow the locking and the eject functions of the disk tray to work as normal for me in my ProDesk 600 G3 units. I printed this with Hatchbox black PLA at 195 degrees and 100% infill. The M3x8 screw was a bit long but it...

I discovered that the outgoing feed tube was consistently detaching from the extruder clip supplied by Mosaic for the P2 and MK3 printers. To my observation, the provided extruder clip proved to be insufficiently deep, resulting in the tube failing...

<p>Use the same screw as before to attach this piece</p><h3>Print Settings</h3><p><strong>Printer Brand:</strong></p><p>Prusa</p><p> </p><p><strong>Printer: </strong></p><p>I3...

I used half-inch long springs, hot glued in position instead of rubber grommets. The result is a noticeably stiffer setup. I haven't yet put it to the test on my X-Uav plane. You can find an assortment of these springs at Harbor Freight warehouse.

This is a Grommet

Needed a grommet for my car firewall

Tech Spec: TaznaX Grommet\nConfirmed Diameter Unknown.

Some kind of hole cover or cable grommet, made on request.

... canvas or a tarp. ...Identical pairs snap together with fabric in between to form the grommet. I made this to repair a canvas laundry basket on which the handles had broken. ...The grommets allow me to use a rope as a handle as shown in the picture.

The outer grommet is 16mm in length (without head - 14mm dia) and the inner grommet is 13mm in length (without head - 12mm dia) to allow the insertion of a small piece of foam rubber to apply some drag when pulling the leader. The box ws 12mm ply...

I crafted this custom grommet to seal the hole I drilled into the kitchen island after adding devices underneath the sink, as clearly visible in the accompanying photograph.