2 grommet 3d models

I created this grommet that I use when I cut 2" holes in sheetrock or Desks to hide cables in-wall or at custom locations. ...Cable management necessity

Using the following options: Grommet_Diameter = 60 build_plate_manual_y = 80 build_plate_manual_x = 110 Hole_Diameter = 40 build_plate_selector = 2 Font_Size = 9 Letter_Spacing = 1.5 Top_Text = Customized Version of Thing:298718 Created with...

Ikea Linnmon table tops lack pre-drilled holes for routing cables through them.\nThis 2-inch grommet fits perfectly in a hole you would drill yourself. I used a 2-inch hole saw, but you could also use a jigsaw if you're careful. Do not drill closer...

Customized version of https://www.thingiverse.com/thing:1030514 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1030514

Emax Babyhawk 2 HD - Grommet to prevent rubbing of power cables.

This is a super simple grommet I pulled together when building my home network cabinet. &nbsp;Simply cut a 2" hole in your cabinet and screw this bad boy down in it. ...&nbsp;Voila!</p>

Crafted with precision, this intricate design boasts a 3/8 inch interior hole, perfectly complementing its 1/2 inch outer diameter. ... The mastermind behind this creation was none other than myself, who brought it to life using the versatile tools of...

... in the bathroom. ...So I drilled a hole, measured twice, and designed a grommet to protect the cheap particle board from abrasions.Made in Tinkercad, it is easy to print and useful if you remember to print it before you put the lines through the hole.

http://www.thingiverse.com/apps/customizer/run?thing_id=273159 Instructions Using the following options: Hole_Diameter is set at fifteen millimeters Top_Text can be customized with your message or image Build_plate_manual_y is located one hundred...

Fits a 2-inch hole without a cover. Created using free Sketchup in inches. When printing with Cura 3, I had to scale up the model to 63.5 millimeters in both x and y directions, while z remained at 31.7503 millimeters. ...Note: One inch equals 25.4...

This is designed as a 2 inch grommet, made out of two pieces that screw together for panels, fabric, or other thin type of material. The two halves screw together in about a half of a rotation. I printed with no Brim or Supports, and it printed...

... used to channel cables through? ...Well, I needed a cover for one that wasn't being utilized so I could reclaim my workspace. I designed this for a 2-inch opening that fits tightly, ensuring it remains securely in place. ...Just print and insert!

Key settings used in its creation include case thickness of 3.5, $fn value of 35, no cable hole diameter, a case hole diameter of 19.05, catch angle of 55, a thickness of 1.2, slice angle of 80, catch height of 1, case overlap of 3, three catches,...

I redesigned one of several covers available for the Skelestruder filament sensor by combining it with the incoming grommet holder from the Prusa MK3s lid and ended up with a filament cover that holds both the grommet and tube coming in from my...

Customized version of https://www.thingiverse.com/thing:273159 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=273159

Customized version of https://www.thingiverse.com/thing:4372453 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4372453

This project originated from Tinkercad and can be edited directly on the website https://www.tinkercad.com/things/4z3n8h5S7wG.

This is a 2-piece passthrough grommet for a starlink or similar cable where you cannot take the ends off. Push the cable into the inner grommet, then add the outer grommet and turn it to fully cover the cable and hole. You'll probably want to...

This is an adapter that works seamlessly with the filament tube grommet designed by Mosaic Mfg for use with the Palette 2.\r\nIt attaches directly onto the filament clamp of the Titan Aero.\r\nI also include a support guide to keep the tube in place...

A personalized version of the design found at http://www.thingiverse.com/thing:38819 was created using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=38819). ...For this specific model, the following parameters were used:...

Customized version of https://www.thingiverse.com/thing:273159 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=273159

A personalized version of the design available at http://www.thingiverse.com/thing:38819 was created using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=38819). ...To print this model, use these specifications: catchAngle...

People need a reliable way to manage their cluttered workspace, which is why a sturdy 2-inch desk grommet is an essential tool for organizing messy wires.

Acquired from Grainger at $5.55, this desk grommet was custom-made due to unavailable accurate models. ...Employing digital calipers for precision, it offers four adjustable configurations to match various cable grommet positions.

Dual Grommet, large hole is 1' and small hole is 5/8, countersunk for a 10-24 allen bolt i believe, EMS EHLERSMOTORSPORTS

I couldn't find a suitable wall grommet for my antenna cable, so I took matters into my own hands. This DIY solution is specifically designed for a 3/4 inch (19mm) hole and RG-8X coax cable with an outer diameter of about 6.4 mm. The flange has an...

The protective sleeve fits snugly into the 2" hole, and the cover clicks securely in place and can be rotated after assembly. If anyone wants additional sizes let me know, because now that the template is all set up I can quickly create alternate...

... is now set up to create alternative diameters easily. Printed using ABS on a Replicator 2X with settings of 10% infill, 3 shells, 0.2 MM layer height, no raft or supports. ...As per user request, the two parts are now available as separate files.