2 axis gimbal 3d models

To achieve this, specific options were utilized such as ring_height_step set at 0.0, pin_cap_gap at .45, pin_cap_width of 4, ring_spacing as 1.5, mesh_resolution at 70, number_of_rings set to 3, Build_Plate_Manual_Length and Build_Plate_Manual_Width...

Https://Www.Thingiverse.Com/Apps/Customizer/run?Thing_id=73634 Instructions Using the Following Options: Build Plate Manual Length Is Set to 100 Pin Cap Gap is Exactly .45 Millimeters Center Radius Is Now 6 Units Pin Radius Is Currently 2.45 Mesh...

Printing without supports or rafts is recommended, with settings at 10% fill, 2 shells, and a .27mm layer height. Initial stiffness may be experienced but playing should loosen joints. If printing six or more rings, it's suggested to adjust ring...

http://www.thingiverse.com/apps/customizer/run?thing_id=73634 Using the following settings: - mesh_resolution is set at 70 - pin_hole_radius measures exactly 3 millimeters - number_of_rings stands at five rings strong - ring_width has been determined...

... along the Y dimension both before and behind the waste board. ...Additionally, I elevated the X axis by 2 inches to create more clearance between the X axis and the waste board, accommodating any desired length of the new X Carver Z axis assembly.

I've reimagined my XY-Axis Belt and posted it online at Thingiverse - check it out here: http://www.thingiverse.com/thing:1830917. ...The redesign allows for seamless removal of the XY-Axis without touching any critical components of the printer.

This is a simple mount for a PS2-style joystick with board. ... This is used with Arduino compatible 2 axis joysticks to control MeArm robotic arm.

Ender-2 Z-Axis Stabilizer with Bearing Upgrade. You'll Need to Source a High-Quality 698-RS or SS Bearing, Specifically an 8x19x6mm Model. No Additional Support is Required if You Simply Flip the Z-Axis and Print from the Top Surface. ...The Ender 2...

The self-leveling gimbal and landing gear are made from carbon fiber arrows, 3 servos, and printed parts. To build this project, you'll need: 1. Four 10x5mm ball bearings (Duratrax DTXC1535, $4 for 2). 2. A box of Warrior 400 1/2 DZ. HP-Vanes model...

... for overhanging areas and another without. Assemble with 8 M5x16 bolts, 9 nuts, an M5x30 stainless steel bolt, 2 M3 bolts with nuts, and 2 M5 washers, along with a pulley with a 5mm axis diameter. ...Follow the 3D image for detailed instructions.

Optical endstop mount Y axis for p3steel 4.2 by makergal Print instructionsUnassociated tags: p3steel 4.2 Category: 3D Printer Parts

Z axis adjustment screw handle.

... Solidoodle 3). ...It attaches to the z-axis lead screw from above and secures to the z-axis carrier using existing openings. ...Sourced from a local hardware store, the spring and fasteners influenced the design due to weekend availability constraints.

... nozzles will need recalibration of Z axis. ...This mod allows the Z-axis sensor to be moved up and down by +/- 2 mm without adjusting the 4 screws under the bed. ...It is equivalent to raising/lowering the bed.M4x10 screws and T nuts are required.

A remix of the "Elegoo Neptune 2 X Axis Extruder Chain" plate and endcap with the tab directing wires to the X axis shortened to allow for compatibility with https://www.thingiverse.com/thing:4243188, and to reinforce the chain clips on the 40x40...

This was printed with ABS, no supports are needed.BOM:1 - 10x11 Drag Chain6 - M3x6 Flat head screws (Attach the drag chain to the mounts)2 - M3x10 Button cap screws (Attach the support brace to the gantry)2 - M3x10 Flat head screws (Attach the mount...

Cover for the bottom of the Z-axis (where the HBP wiring would otherwise go) on the Replicator 2. ...This is technically a Heyco DB25 (part number 2970) if you want to order the actual injection-molded part.

2.4G ELRS antenna mount for the Axis Flying Manta Frame. The Happymodel antenna fits well. I have yet to try the BetaFPV antenna or others. ...As always with FPV drone parts, print in TPU.

This is a high-performance Y-Axis P3 Steel V4.2 MakerGal Motor Mount designed to prevent motor bending by tightening the Y belt, ensuring a stable and precise printing experience.

Z-axis height adjustable for the Ortur Laser Master 2 With 8 mm lead screw rod Print 4 pieces Lay cube part (rod lead) flat on the print bed

Brass Knuckle style Ender 2 Pro handle with 608 bearing mount for the z-axis lead screw. It works with or without the bearing. ...Prints in two parts and took about 5 hours to print at 50mm/s.

Brass Knuckle style Ender 2 Pro handle with 608 bearing mount for the z-axis lead screw. It works with or without the bearing. ...Prints in two parts and took about 5 hours to print at 50mm/s.

Webcam mount for the Neptune 2 and Neptune 3. ...The Camera mount will slide over the existing X axis switch cover. ...A 18mm screw will be needed to mount whatever webcam you are using.

This is just a remix of the y axis adapter which proved to be too thick for my application with a Laser 2, so I thinned the mounting bracket.

Z-AXIS Top For PRUSA MK 2.5S is spare part  for 3D Printer replacing broken one. Some of plastic printer parts are littlebit crisp after 4 years. I found some stl files with Z-AXIS Top replacement on Prusa web pages. I tried print them but...

I used 2 6/32" bolts with wing nuts to secure the X-Axis Tensioner Mount to the Elegoo Neptune 2 carriage assembly using the top and bottom slot holes of the X-Axis Tensioner Mount Supports may be required when printing for the holes and slots in...

Sturdier Y axis stepper motor mount. ...

This is a Y Axis P3Steel V4.2 MakerGal Motor Mount that secures the motor against bending because of tensioning the Y belt. Print instructionsUnassociated tags: p3steel v4.2 Category: 3D Printer Parts

... optical endstop for Ender-3 and similar The normal endstop is now used, the chopper flag is located on the wheel holder. ... Nut M3 - 5 pcs Screw M3x8 - 2 pcs Screw M3x10 - 2 pcs Screw M3x12 - 3 pcs Source: https://www.tinkercad.com/things/jyBfQaLK3JI

My Ender 3 Pro/2 Axis/ Power Supply Solution + https://www.thingiverse.com/thing:4409466 In use of: https://www.thingiverse.com/thing:5235744/files Meine Ender 3 Pro/2 Achsen/Netzteillösung + https://www.thingiverse.com/thing:4409466 Mein Dank an:...