2 5 inch hdd 3d models

Remix of Randy78s 2.5" HDD Storage Holder which has maximum 10 hard drives, mine is the same but with 15 drives which is pretty much the maximum you can print on a generic 200x200 bed. ...Print Settings Printer: Prusa i3 Clone Rafts: No Supports: No...

Tray adapter for seamlessly fitting a 2.5 inch HDD or SSD into a standard 3.5 inch tray mount is now available.\nHoles are engineered with precision to enable effortless self-tapping using original screws without any hassle.\nThis custom-designed...

... Here are the inside dimensions: 17mm high, 84mm wide, and 114mm long. Plenty of room for all your storage needs. And when you're done adding drives, slip on the cover with its bold inscription: "HDD 2.5" - a stylish finish that matches any decor.

Multi-drive enclosure featuring two slots for 2.5-inch hard disk drives (HDDs) or solid-state drives (SSDs), combined into a single 3.5-inch drive bay.

Support for three 2.5-inch hard drives is available with a footprint equivalent to that of a standard 3.5-inch hard drive screw.

A Remix of miginv's "Raspberry Pi B+/2 + HDD 2.5' case"To be fair and possibly spare your time:This model is not fully 3D-printing optimised.eg the first layer has some sharp corners and my remodeling is not perfect.That being said: It worked out...

The regular HDD carriage for 2.5" hard disc drives or SSDs is restricted to 9mm in height, which means the maximum capacity is capped at 1TB. This is because all standard HDDs with capacities of 2TB and above exceed the 9mm threshold. To overcome...

You can purchase a cheap mSATA flash card and an equally cheap adapter board to make your own budget-friendly 2.5" HDD replacement by printing this design. The square and round openings are strategically designed to minimize filament usage and...

I wanted to add a second 2.5" HDD to my Dell XPS tower pc. The machine came with one plastic caddy for the first slot, but not one for the second. Trying to source a caddy was impossible (at least in the UK)! So I designed a simple printed caddy. ...

The PC did not have 2.5" HDD mounting hardware so I decided to design and print two holders for my RAID-set drives.The holders are printed out of blue PLA, are glued to the PC chassis with E6000, and have a width that allows for a 3mm rubber spacer...

To squeeze a 2.5" HDD I designed this extension. You'll need : SST-CP12 cable - bought one for £6 on amazon 4x M2.5 12mm male/female standoffs (only had 10mm, so added a nut) 4x M2.5 6mm male/female standoffs 4x M3 6mm screws for the drive. Make...

I'm working with a Raspberry Pi Zero W combined with a compact 2.5-inch hard drive.

A 2.5-inch HDD can still be secured using the existing case mount screws at the bottom. The model should be relatively straightforward to understand. ...To print the final version, you'll need to download and use the "small" STL file, as the other...

Odroid H2 2 3.5"HDD NAS Designed in Fusion 360, All panels printed with ABS, side panels should be something stiffer like aluminum. HDD mounts are printed with TPU For structural rigidity, side panels should be made with alu panels. ... Parts needed:...

Xbox One S-style HDD cover

Remix of Randy78s 2.5" HDD Storage Holder which has maximum 10 hard drives, mine is the same but with 15 drives which is pretty much the maximum you can print on a generic 200x200 bed. Print Settings Printer: Prusa i3 Clone Rafts: No Supports: No...

Secures a 2.5" SATA hard drive or SSD into a modified "phat" PS2 casing. Prints with minimal infill since the mount is designed to flex slightly, allowing it to fit snugly within the console. Simply attach the drive to its mounting bracket, connect...

Humans stack ten 2.5-inch disks on top of each other. ... External measurements are Length 142 millimeters, Height 74.4 millimeters and Thickness 110 millimeters.

### German Dieses 2,5" HDD Gehäuse ist gedacht für die neue Generation der 15mm Seagate 4 und 5TB Festplatten. Diese Platten sind billig, flüsterleise, sehr sparsam im Stromverbrauch und können somit direkt über Geräte-USB - auch direkt vom TV oder...

German Dieses 2,5" HDD Gehäuse ist gedacht für die neue Generation der 15mm Seagate 4 und 5TB Festplatten. Diese Platten sind billig, flüsterleise, sehr sparsam im Stromverbrauch und können somit direkt über Geräte-USB - auch direkt vom TV oder...

Now, mounting your 2.5 SSD/HDD no longer requires any screws. WARNING I haven't tried removing an SSD yet, so it's possible that when you attempt it, the pins may break off. Proceed with caution. UPDATE After having to remove my SSD, I was...

Not  was tested Maximum area for external HDD (2.5"): ≥100mmX≤81mmX≤21mm.The pad size is 2mmx2mm.You will need:-2x SupportsIf possible, publish your 3d print on the Make tab.Tips:Paypal:...

I remixed this model adding the HDD Support.. ...

New expanded Version of my first HDD holder.You need 2-Screws (one Front / one Back / see Pictures.You also have 2 mounting Options (see Pictures).Should fit on S720, S920, S930.Sorry for the messed picture order (thingiverse will not accept my...

This simple-to-assemble hard drive enclosure is designed specifically for 2.5-inch drives. ...The case consists of two parts that easily snap into place to securely hold your storage device in position.

Here's a spare rack to keep and recycle your 2.5 inch hard drive safely. It connects with that specific cable. ...More details can be found at http://www.reusing-old-hard-drives.com

Fit 2x2,5" SSDs into Cooler Master Elite 360 tooless 3,5" bay

Portable External Hard Drive Container Holds Six 2.5-Inch HDDs, Including Lacie or WD Models. Dimensions Measure 10.75 x 88 x 8.5 Centimeters Externally, While Internal Space for HDDs Measures 83 x 14 x 80 Centimeters. ... This Versatile Container...

... ...It's Custom-Made to Fit All 2.5-Inch Hard Drives and Solid-State Drives. To Achieve the Best Printing Results, I Recommend Using a Layer Height of 0.2 Millimeters with Support Structures. ...The Material of Choice for This Project Should Be PLA.

This is a basic storage rack for up to five caseless 2.5-inch hard drives, so your hard drives won't be scattered across the desk ;-) Print Settings Printer CTC Rafts Doesn't Matter Supports No Resolution 0.2 Infill 15%