1in square tubing 3d models

This is the motor end and top mount for a Kossel Modified for standard 1in OD Square Aluminum Tube. With this method you won't need any expensive 1515 extrusions or 2020 extrusions. Just pick up some 1 in Square Aluminum tubing from your hardware...

Customized version of https://www.thingiverse.com/thing:1720245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1720245

This is for plugging the end of a tube that has a 1in ID.

...I printed at 100% in fill for strength but you can probably get away with 15% if you don't plan to have much weight on it. a 1in x 1in double sided mounting square was used to mount the peg to the wall. ...design can be scaled up to meet your needs.

A hanger to support hanging plants (or anything) from the side of square tubing. I printed with supports.

... new version was designed for improved printability and created in Fusion360 instead of OpenSCAD. The provided .stl file should work for 1/2-inch (12.7mm) square tubing. I printed eight of these to join the square tubing for a printer enclosure.

... new version was designed for improved printability and created in Fusion360 instead of OpenSCAD. The provided .stl file should work for 1/2-inch (12.7mm) square tubing. I printed eight of these to join the square tubing for a printer enclosure.

For assembly, follow the instructions provided on the Multiwii website and notch 2ft length square tubing for extra strength. Mount outrunners with mount.stl and secure housing_base.stl and housing_top.stl using M3 bolts. Connect RX module to flight...

The .STL file contains the nominal dimensions for 1/2 inch square tubing, but you may need to make the inside dimension a little smaller (in the Customizer or in OpenSCAD) to give an easy slip fit. I used a very similar design to build an...

Create a modular square tubing tower by printing individual parts and connecting them via bridges. Adjust scaffold lengths for each piece to ensure proper assembly, while staying within your build volume. For stability, bottom pieces should be wider....

Purpose: To check a square tube surfaces for parallel Background: I am building a precision linear delta which will use square stainless steel tube as the vertical ways. Using Whitworth's 3 plate technique I can make one side of the tubing flat, but...

This is my design for a hinge to be used on a multicopter arm to be used on any multicopter with a 14mm square tubing arm. It could easily be scaled to be used with other tubing diameters. I'm sure it can have other uses as well. I have not...

As it is I use the slic3r PE 1.41, which has a feature to click a face and make it the bottom. Here's what I'm using for 1"/25.4mm steel tubing: center cube: 24.6 protrusion: center: 22.6, end: 22.2, length: 33 spacer: 5 rounding: 1.5 Print...

I'm using 25.4mm/1" square steel tubing and the inside size is about 22.2mm. Make the inside size a bit larger near the center and then taper it down to the end, which means you might need to pound it in for the last bit. It also means it may be hard...

this is designed to fit 1in square tubing i picked up form the big box store. Here is the square tubing I used. ...I used a hack saw and cut off a 12" piece but this can be adjusted for your needs...

Used to hold a caster in a 1" square tubing leg

This cap is designed to be compatible with 2-inch, 18-gauge square tubing. ...To use it, simply print and insert into the tube for a perfect fit.

A 3/4-inch square tube serves as the foundation for constructing a quadcopter DT750 mount, providing stable support.

This is a joint to make an icosahedron with square tubing, or wooden sticks, or anything with a square cross section. As supplied, the model provides a 25 mm square hole, 37.5 mm deep. To make the complete icosahedron, you'll need 12 of these,...

This is a joint to make an icosahedron with square tubing, or wooden sticks, or anything with a square cross section. As supplied, the model provides a 25 mm square hole, 37.5 mm deep. To make the complete icosahedron, you'll need 12 of these,...

This provides the complete set of all nine possible square tubing connectors. Also provided is a special fixture to allow you to find the optimum fit for your tubing. The default STL files include all the fittings for 1/2 inch (12.7 mm) square...

An adapter for mounting a common office-chair caster in square steel tubing. It's designed for use with standard ⁷⁄₁₆" caster stems and with 16-gauge 1⅛" steel tubing. I used it to fasten [AGPTek™ locking...

A snap-in adapter for mounting a common office-chair caster in square steel tubing. It's designed for use with standard ⁷⁄₁₆" caster stems and with 16-gauge 1⅛" steel tubing. I use it to fasten <a...

We have an aluminum pergola with approx 1in square tubing across the top. Sometimes they fall out into the abyss, never to be seen again. :-) Believe it or not, I have had a tough time finding a replacement part so decided to throw together a piece...

Maybe you find this piece handy, too?! Just print it and mount it to a squared timber or square tubing with zip ties and you're good to go! You can use it for round vessels with a maximum diameter of 8,60 cm (about 3,38''). If you like my work,...

Square tubing cap replacement for tube 20x35x1.5mm

Revolution 2x72 plugs Simple 1.5" square tube end cap plug for square tubing with a wall thickness of ~0.1875".

This is for my robotics team to bind two pieces of 1x1 aluminum square tubing with a bracket and ensure it is square.

Designed this adapter to mount to a homemade disc golf cart. ...Simply zip ties to 0.8" x 0.8" square tubing.

I designed this tool to form pre-coped 1.250" square tubing up to 90° or less. ...It helped keep the tube straight so welding the seams was easier.