1:12 weapons 3d models

Version 1 had some sag to it, there was not enough support to keep the motor/hotend from tilting forward a bit. This version added some extra supports to reinforce it against that. The way this is set up is so a standard NEMA17 (for example - if you...

Update #1 6/22/2015 MKII I finished the initial design of the hull, keel and rudder. I have printed the keel and rudder with good success. I have posted pics of both of them finished. The keel has 34 dimes in it to act as counter balance. I am...

..Assembly tips: 1 - Take your time gluing the model together and enjoy the process. Give some thought into which parts to glue together as groups and then gluing the groups together. Let the glue for each group set completely before combining...

I chose red because it looks mean, and it'll make people think twice before messing with my quadcopter! **EDIT 9/03/2016: Removed accidental hole from the bottom of the longest landing gear. Print Settings Printer Brand: RepRap Printer: Folger tech...

For the ones shown above I used matter hackers High speed TPU, (https://www.amazon.com/gp/product/B08BC7X8HQ/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 ) which has a shore hardness of 95. This was the only TPU I had on hand at the time so feel...

Oh and it has RGB LEDs and a front mounted controller, along with a connection at the rear to plug in any external RGB lighting, such as my laptop underglow:...

My prints ended up being around the same weight as the stock hammer (9g). Radioactive's draw extension:For context, Radioactive has a guide/product for extending the draw on your Hammershot for more oomphTo push this further, you can use the extended...

It is Half the height of the Sector Mechanicus Walkways and the same as the new Salvation killteam.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my other designs:https://www.thingiverse.com/thing:6456439 -...

For the vertical part I used only 1 layer width and only 15% infill. Roll and Pitch Motors 2204 450KV motor. I used 2 of these. <br /> <b><a href="https://nl.aliexpress.com/item/33030297601.html?spm=a2g0s.9042311.0.0.27424c4djLtPAl">Yaw...

This is the code I use in Cura: (yes this is the complete End-Code) ``` G91 ;Relative positioning G1 E-2 F2700 ;Retract a bit G1 E-2 Z0.2 F2400 ;Retract and raise Z G1 X5 Y5 F3000 ;Wipe out G1 Z10 ;Raise Z more G90 ;Absolute positioning M106 S0...

After adding two 1.5mm high spacers to the bottom 2 laser mounting holes it looks perpendicular. There are 2 photos included that show the before and after of this. When assembling this, I found it easier to attach the laser wiring before mounting...

Feel free to change it if you want it to be another pin col = digitalio.DigitalInOut(keyboard.col_pins[0]) row = digitalio.DigitalInOut(keyboard.row_pins[0]) if keyboard.diode_orientation == DiodeOrientation.COLUMNS: col.switch_to_output(value=True)...

Also the ingredients/directions will be a bit general because: 1) I heavily relied on the advice of local guitarist since I myself know very little. 2) I was building the guitar as a birthday present and sort of learned most of the stuff I know from...

this model is based on real data therefore this is a realistic buildings and streets setup of Astana, Kazakhstan 7 building groups are setup so that you can add variety to buildings (color materials and/or textures) Groups can be turned off/on UV...

Custom Section version history v0.0.1, 2016sep13 initial version v0.0.2, 2016sep13 changed support to interleaved pillars. v0.0.3, 2016Sep14 changed support to perforated walls. lowered blocks. thicker walls around air chamber. added foundation to...

A remix of http://www.thingiverse.com/thing:11978 to remove the top bar in the links and instead provide springy clips which can be easily removed and replaced to keep the cables in the chain, while still allowing them to be replaced without having...

The factory sealed, hazardous location fixture is protected by a copper-free aluminum housing with an epoxy powder coated finish.The EPLC2-LB-50LED-RT-600V is a Class I, Division 2 and Class II, Divisions 1 &amp; 2 hazardous location light fixture...

It is a printed 1/4"-20 standard tripod thread. When I printed the original I found that the rear case was a fairly loose fit for me so I added 0.1mm thickness to the rim in the rear panel to make the fit tighter. Your mileage may vary depending on...

...--> https://www.amazon.com/gp/product/B07QW58TZH/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 There are more pics of the shorty version here --> https://imgur.com/a/UoAlEnf, and more pics of the tall version here --> https://imgur.com/a/RjQQ7zu.

..Assembly tips: 1 - Take your time gluing the model together and enjoy the process. 2 - I used E6000 sticky craft glue to put this model together. The sticky glue allows more time to position the parts than a fast drying superglue. I have 'fat...

Choose from a diverse array of models: 1. Bedroom Furniture: Expertly crafted bed designs that add elegance to your renders. 2. Blue ray Box: Bring sleek home entertainment setups to life with our realistic DVD cases. 3. Book Collection: Stock your...

None of this affects how well the scroll ring works.\r\n\r\nEdits:\r\n\r\n- 2020-02-02: Original version.\r\n\r\n- 2020-02-08: I've reworked the wave on Component5 and Component9 also received a couple corrections.\r\n\r\n- 2020-02-09: I've continued...

I wasted a couple hours with this stupid mistake) x1 6.25u [Costar Style stabilizer](https://www.amazon.com/dp/B07K8HP6KC/?tag=emeraldheart) (this is a multi-pack that also includes a longer one for space-bar which you don't need for this project)...

I came up with a hack that uses a MosFET (rated for 120A actual rms current!) to switch the heated bed's power from an Ultimaker 1 electronics board without using any current from the UM1's original power supply. Of course, you'll need a second...

Printed in timelapse) Subscribe to find out more support free 4K Time-lapse video: Subscribe Now!http://www.youtube.com/iczfirz Addiction to 3D Printing? Watch these time-lapse! ... https://youtu.be/uNqqN5Ao_hI <a...

Since the illustration is at a 1/3 front angle, this was mainly a process of choosing how long and squat the whale should be. I tried loads of versions but found that something a bit more realistic offered more flexibility. Next, I used some simple...

# What you will need for this project: - Aluminum Profile 40mm x 3mm x length of your light - 12V LED Strips (I'm using warm white, cold white and a bit of red) - 12V power source for the LEDs and a way to connect them to it - 1m string - 1 plastic...

If you are using a multimaterial unit, all the parts are set for extruder#1, except the finger (part Finger.gcode) and the second colour for the cover of the box, that are both set for extruder#2 DESIGN IMPROVEMENTS All small changes. I included 4...

The mount base will be 25mm x 50mm (so that it tiles nicely on a 1" pegboard), and large loop sizes will overhang the top/bottom/sides of the base. DirectionsNavigate to the OnShape Document. Go to the Peglock Loop Mount tab and change the parameters...

You will need the following parts: MK2A 300x200x3.0mm PCB Aluminum Heatbed If you search for this term on aliexpress, you'll find it (MK2A 3002003.0mm RepRap RAMPS 1.4 PCB Aluminum Heatbed heated bed MK3 For 3D Printer / MK2B 300x200x3.0mm). 8mm x...