1968 firebird model

They were sold to me as "boat nails", feel free to substitute them for something else and adjust the model accordingly. For the spark gap I used a couple of bits of single stranded wire, these can be substituted for something else, multi-strand...

Details and models may change as I continually improve it. Please see the pictures for individual printing instructions. If the spur gear for the table binds when rotating the table, loosen the stepper bolts, push the stepper inwards, and tighten....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

Note: Scaling down the model too small may not work on all printers. The smaller the part, the more precise your printer should be. 1/2 scale should work well without extra precision. Any smaller will need a printer which supports a step of .05 mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 7 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

Quick release (keyed-slot) analog module bay for Walksnail Goggles X and DJI V2.Have a look at the awesome original model first. This remix replaces the main body and the “B” mount adapter plate that gets screwed to the back of the main body. The “A”...

Mine are quite tight and don't rattle or move.I included gcode files for Ender 3V2 but slicing the model is not complicated. Place the top half upside down. It needs support because the blade holders are on the bed and the back is higher. Supports...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Warning: At time of publishing this model is untested with an actual whambam3d build plate. Be careful to read all instructions before you start and follow them as written. You can damage your 3d printer if you are careless</p><p>The WhamBam3d...

For this I created individual bodies and combined them as a group, so that they can be imported again as a model in the slicer.For the Arduino I just put a small box on the backside. The cables can be hidden there nicely and you can also set it up...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The tolerances on these can be somewhat tight, but they came out beautifully on my Bambu X1C.Model specific notes follow:cards_box_1.stl, cards_box_2.stl - Print one of each. You can add color on layer 4 or 5 (depending on line height) to make the...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

half lengths are the way to go with this barrel.yes.All of the models require no support and the whole build requires little hardware. Here is the parts list for extra hardware:</p><figure...

R/Cers there are included ailerons for micro setups!\nNotes: On my printer (which isn't working so great right now) this works out to 3 and 4-layer parts (mostly), so the whole thing took about 1/8 spool of filament, and all of it prints in about 4...

Signal dimensions are taken from the book Model Railway by B.V.Barkovskov et. al. Published - Moscow 1989 - ISBN 5-277-00181-6 p78-79. Additional documents with dimensions were found at the Russian scaletrainsclub.com forum. A very comprehensive...

The 3D model is solid. To make the vane pattern in it, set the number of top and bottom layers to zero and select a grid or triangular infill with a distance of about 10mm between lines. To ensure rigidity, aim for at least 1mm walls (3 perimeters at...

... screws. Now you can start the tank with the key and load it without opening it. PS: The original model has more than 200 rivets that the FDM Printer neither sliced nor printed. ...So if anyone wants a riveted version for a resin printer...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

Description: https://youtu.be/G9-N-nIqc4g Assembly: https://youtu.be/2hdSGDdjpeQ Torque Capabilities Please note that I designed this CVT for a demonstration model, it's not intended to be used as an actual transmission. How This Works - Watch the...

I have not printed/tested these myself - I will remove this note when I get confirmation that everything fits correctly. lrs-350_foldingCover_front_blank.stl this one is completely blank, you can add whatever cutouts you need for components of your...

... but found it lacking in designing the parts I wanted. Onshape was easy to get started with and proved to be up to the task. You can find my Onshape model here: Tiny Tensioner for Creality_Ender_3,_3_Pro_or_v2. ... Category: 3D Printer Accessories

  I've been using the one in the picture for a few weeks and apart from not looking as pretty with the cam open, there's absolutely no difference in performance.I think I have allowed enough room to print this model with a .6mm nozzle but if you are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...