18650 tray 3d models
52519 3d models found related to 18650 tray.
prusaprinters
Designed something that can be printed very quickly (~30min) in vase mode to hold/organize nine 18650 cells I recently recovered out of an old laptop battery. Print instructions0.4mm nozzzle 0.2mm layer height 1mm solid bottom of vase vase mode!
cults3d
This is an 18650 battery tray for the Taranis Q X7. It has mounts for a charging protection board and USB charging jack. It also has mount for a battery cut-off switch. The Q X7 will run on the USB cable once it is booted up. When you are in...
thingiverse
This is an 18650 battery tray for the Taranis Q X7. It has mounts for a charging protection board and USB charging jack. It also has mounts for a battery cut-off switch. The Q X7 will run on the USB cable once it's booted up. When you're in flight...
thingiverse
*** USE AT YOUR OWN RISK! *** *** USE AT YOUR OWN RISK! *** Assume you are using 18650s that are at least capable of 15 amps (20a minimum is highly recommended) I have included minimal instructions. If you can't figure out how to wire this...
thingiverse
**** NO POLARITY PROTECTION **** **** NO POLARITY PROTECTION **** **** NO POLARITY PROTECTION **** USE AT YOUR OWN RISK! Basically just used the attachment section, thanks for doing that work! I wanted to be able to swap 18650s. They...
thingiverse
Customized version of https://www.thingiverse.com/thing:3688335 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3688335
thingiverse
Customized version of https://www.thingiverse.com/thing:3688335 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3688335
thingiverse
... packs are a tiny bit loose. Add padding to it as necessary. It is not ideal for high vibration applications if you are using PLA like I did. Currently it's in an 74" EF Edge 540 with a 35cc engine. Still working! i only resized it to fit 18650
thingiverse
Batteries supplied with my radios were not reliable and I had some 18650 batteries that I decided to fit in these walkies. I used 10mm wide adhesive copper foil tape to wire the batteries in the tray. WARNING: original battery voltage says 7.4V but...
thingiverse
You're looking at a simple 4x4 tray for 18650 batteries, designed to align them in a neat cubic or rectangular pattern for easy tab welding with a spot welder. The idea here is to have the walls of the batteries touching on all four sides, making it...
thingiverse
Customized version of https://www.thingiverse.com/thing:3555258 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3555258
thingiverse
Customized Version of Thingiverse's ID:65356 Created with Customizer! ...Thingiverse.com/Apps/Customizer/Run?Thing_id=65356 Instructions: Using the Following Options: Spacing: 1.2 Height: 15 Rows: 1 Columns: 2 Corner Rounding: 4.0 Diameter: 20 Label...
thingiverse
Customized version of Thingiverse: The Wooden Gear Set #7 Created with Customizer! ...www.Thingiverse.com/apps/customizer/run?thing_id=48235 Instructions Using the following options: height 8mm base 0.5 inch...
thingiverse
I designed this to be able to easily drill holes in an 18650 tray to build some Dave_C Nano Longrange quads. ...
thingiverse
Compact and simple, but nice looking, 18650 desktop tray to hold 8 cells. 19mm inside diameter, 15mm vertical coverage of the cell. Quick print @ just over 1 hour, minimal material, only 14g filament. ... Edit 10/25/22 - added another STL that holds...
thingiverse
Battery Holder for Any 18650 Battery Configuration for Electric Bicycles or Similar Uses. All sizes, starting from 2s2p up to 10s10p, are pre-programmed. Find the one you need by using text search on the "Thing Files" page. To obtain an STL file...
thingiverse
I've printed 2 myself: one x8 that is configured 8S1P with each slot individual which I use with a set of 8S balance leads with aligator clips soldered on so I can quickly configure charging between x1 and 8x 18650 cells with my iCharger 308Duo. I...
prusaprinters
... matter)</p> <p><strong>Notes:</strong></p> <p>I printed in PETG. I have not tested in PLA but I highly recommend PETG if you plan to use these trays as daily items as I do, as I suspect PLA may degrade in springyness overtime if routinely flexed.
thingiverse
I made it replace the Lead Acid batteries by building a 4x6 tray, copying the stackable design found online. The hole size is 19mm, which accommodates the 18.5mm diameter of the Li-ion battery. I tried different sizes and 19mm worked best. Print the...
thingiverse
Customized version of https://www.thingiverse.com/thing:2953989 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2953989
thingiverse
Customized version of https://www.thingiverse.com/thing:2953989 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2953989
thingiverse
Customized version of https://www.thingiverse.com/thing:2953989 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2953989