17mm ball mount socket 3d models

... to offer more flexibility. ...The threaded ball sockets are available in three distinct lengths: 37mm, 51mm, and 61mm. ...I also separated the STL files so you can print the nut and washer individually if needed.

Mash-up of a locking ball and socket arm, and the Octo-Pi camera holder. I wanted to be able to adjust the angle and range of the camera - and the original hinge on the Octo-Pi camera enclosure / mount was weak, and had limited range and positions.

This is a reworked version of NathanMichaelMoore's ball-and-socket camera mount, modified to be compatible with the Prusa i3 MK2.5. The current design of the MK2.5 extruder features a front cooling fan positioned at a 45-degree angle, which poses a...

I crafted this iPhone holder specifically for time-lapse captures of prints on my MakerGear M2, mounting snugly in the left corner ahead of the Z-axis knob.\nIt was designed using an iPhone 5S, and you can easily scale up or down in size within the...

... to install this wall mount instead. Note that the ball and socket nut used in this design is identical to my original one found at https://goo.gl/hur6CM. ...If you already have those printed out, all you need to do is print the camera mount part.

This creation brings together the effortless connection of ironhalo's arm with the robust stability of rwohleb's ball and socket joint system.

To give my OSVR camera a secure hold, I created this mounting system. Although it was made for a lightweight camera, the design makes it slightly flexible. However, you can adjust the thickness in the Customizer to accommodate heavier cameras as...

I created these for my friend, who likes the ball and socket design but wanted to mount his sensors to the ceiling without printing too much plastic. I redesigned the socket from scratch, following the original design closely. I used the same ball,...

I found my camera was not staying in the same position well enough so I made a Ball and socket version that can be tightened down. Print Settings Printer Brand: Prusa Printer: i3 MK2SRafts: No Resolution: .2 mmInfill: 20% Notes: This uses a...

Note that once the wire is glued to the socket part with the lever in place, it's impossible to pull the ball out of the socket without destruction, even when the lock is fully disengaged. Printing ---------- I successfully printed it with a 0.8 mm...

Remix of the ball joint (https://www.thingiverse.com/thing:4193227) with supports that go with the arm mount (https://www.thingiverse.com/thing:2842300). ... I also modified a bit the knob to allow for shorter screws.

Remix of the ball joint (https://www.thingiverse.com/thing:4193227) with supports that go with the arm mount (https://www.thingiverse.com/thing:2842300). ... I also modified a bit the knob to allow for shorter screws.

A reimagined version of DavePosH's iconic mount has been crafted, boasting a dual-sided ball joint that empowers users to seamlessly attach supplementary arms, thereby expanding the range of motion and enhancing overall versatility.

Flip the ball 180° for better results.Printed for the old gen IKEA Kappland lights before they switched to micro USB. ...Should still work for new ones though.Mount with 2 M3x8 and 2 M3 T-nuts.

The socket on my Wizgear phone holder broke and I needed to print replacement threads after they snapped off from several years of use. ...Print with support from the plate only to take care of the centering overhang.

When you need a particular angle for your Articulating Raspberry Pi Camera Mount that's not easily available via the typical connectors. ... Printed at 50% infill with 4 perimeters and supports.

The device clicks into place once printed, requiring only a few minutes of assembly time. ...To secure it firmly against the wall, I opted for industrial-grade mounting tape, which also enabled me to swiftly attach the sensor component.

... with cameras. ...After getting them both working (an RPi camera and an old Logitech C170) I threw this remix together to allow for adjustability and length. The Octopi server is mounted on the side of the first printer. ... Category: 3D Printer Parts

Brodit ProClips) to a 17mm ball (used on some phone holders), I have offset the ball to one corner of the mount to allow for better visibility in some situations. Has been printed in ABS and stood up to one of the hottest British summers on record...

This bracket will attach to the center console in a Mondeo MK5. ... The 17mm ball has a little support at the button, which needs to be filed of after printing.

This adaptable ball socket design can be tailored to fit snugly onto any ball fitting, providing a flat mounting surface to securely attach objects using double-sided tape, adhesive, and other fastening methods. Specifically, the STL file included...

What is this?This is single piece adapter from GoPro mount to 17mm ball, commonly used for automotive phone/nav/camcorder holders. It is configurable so you can adjust it for your specific need. You must obtain phone mount yourself. I used Baseus...

... ... Lengthened the stem and thickened body version of Garmin Quad Lock Adapter (17mm ball to Quad Lock Female) by andybcole - Thingiverse Fusion 360 file included so you can change ball size etc. ...but I warn you, its not a pretty timeline :)

Remix of 3DP's holder with a shortened base and a smaller (17mm) pressure mount to fit standard discount store nightlights where the default nightlight cover can be removed.

This is an adapter plate for connecting devices with a 17mm mounting hole to plates with the 4-hole AMPS pattern, commonly found on products such as RAM Mounts. With this plate, you can secure your Garmin Nuvi base within a RAM mount (Image...

I don't like stick on mounts, vent mounts, suction cup mounts, and the pro-clip mount for these cars goes into the passenger seat too much. Anyway, I wanted to use the ashtray since that is an easily replaceable part and is removable. If I go to...

Elegant solution utilizes Ram's versatile GoPro mount to securely fasten Garmin's Nuvi GPS device.

Simple design to use my Ram GoPro mount to hold a Garmin Nuvi GPS. Category: Camera

FCAD files for ball sockets

FCAD files for ball sockets